Notes

15 Funny People Who Are Secretly Working In Repairs To Upvc Windows
Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they do not rust or rot.

It is essential to clean and oil UPVC doors and windows regularly. This will reduce repair costs as well as increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and may even be fatal. It is important to take the time to ensure that you're doing all you can to ensure that your windows are in good shape.

For single pane windows, it is fairly easy to replace windows, and the new one is usually able to fit into the frame of the previous one easily. However If you have double pane windows that are held in place by internal beading it will be more difficult to get rid of the old panes and put in new ones. In this instance you'll need to source some plastic spacers that will aid the new pane in being able to fit properly into the frame of the window.


If you are going attempt to remove the glass panes yourself it is crucial to wear the appropriate safety equipment, including thick gloves and protective eyewear. You should also lay down a drop cloth before you begin working on the window panes to ensure that any shards of glass fall onto the fabric and not on the floor, where they could be trampled under.

It's a good idea to tape the gap once the glass has been removed. This will keep drafts and water from entering your property until a professional comes out to repair the window. It also acts as a barrier, deterring any intruders to gain access into your home. If the gap between the window and the door is substantial, you may need to consider an alarm system that has a window. This will provide the best of both.

2. Sagging

Upvc windows and doors are a cost-effective, durable and energy-efficient alternative to timber windows made of sash. In time, they could be affected by a variety of issues such as sagging. A window that is sagging can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to shrink, it's crucial to act fast to stop the issue from becoming worse.

To repair a window that is sagging, you can try repositioning the hinges. To do this, you'll need open the window so that you can access the frame. Then, using the screwdriver, you'll be able to remove the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. After you've repositioned the hinges, shut your window and check for fitting. If you're satisfied with the fit, tighten the screws until they remain in place.

If you are unable to reposition the hinges, you might require replacing the seal. As time passes, rubber seals lose their elasticity and dry out which causes them to loosen. If this happens, it's essential to replace the seal as soon as you can to ensure that your uPVC windows are watertight and safe from drafts.

UPVC handles can also loosen up. This is often caused by screws that have become undone over time, but it can be due to the handle mechanism getting worn out. It's a good thing that it's simple to fix a loose uPVC window handle yourself. First, you'll need close the window and perform a test to ensure that it fits. The corners of the sash should be aligned with the casing joint. If it does not, you can use the screwdriver to loosen up the handle. Then, you can turn the mechanism into position.

3. Water Leaks

If you wake up to wet floors and damp walls each time it rains, it is important that you take action. Windows that leak water do not only lead to the degrading of the structure of your home but also hinder your efforts to regulate the temperature in your home. Most often, uPVC window leaks are caused by a damaged or missing sealant.

This is a simple fix that can be completed by any DIYer who has the ability. Depending on the severity of the problem the caulking that was used up may require removal before a new layer of caulk can be put on. When full report is time to uPVC repair, it is important to avoid 'over-caulking'. This will only make your window more difficult to clean and lower its energy efficiency.

Check that any drainage holes do not have debris in them and that the sill pan has been properly angled to allow the water to drain from the window. In more serious instances, you might need to consider replacing the window.

Moldy sills and rotten ones are other signs of water leakage. This fungus thrives under damp conditions and can spread quickly throughout the house.

It is also important to note that if the leak is coming from between the glass of your double-glazed windows, it's more likely to be a problem with the glass seal rather than the frame or sliding. Again this can easily be repaired by an uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and blow open in a breeze, it may be hinges that are at the fault. Anyone with the skills to fix them can replace the hinges in a matter of minutes.

Like all mechanical parts hinges will be damaged over time. The process of replacing a hinge on a window is an easy procedure, but it is easier if you have someone to help hold the frame up.

Make sure that the uPVC hinges are open and closed in the correct direction. Look for the arrows that are on each hinge to determine which way the window should be opened.

The issue could be caused due to opening the window in the wrong way or a faulty installation in the factory. Sending us a photo through our website can often solve the issue. We are more than happy to offer assistance.

Regularly lubricating the hinges is essential. Applying an engineering lubricant that is light to the hinges is an ideal method to accomplish this. We suggest using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window to open and close more easily. It can also stop corrosion and decrease the chance of sticking. It is recommended to do this once a year. WD40 and other solvent-based lubricants should not be used since they could damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by a few different factors. The hinges can also be disaligned as a result of wear, which can cause a gap where the sash meets frame. If they're beyond repair, it could be necessary to have them realigned. In addition, the interlock could be disaligned. This is located on the hinge's side, and could require to be cleaned. In some cases it might be necessary to replace these.

The next common reason for draughts is window seals. They are susceptible to being worn out or damaged over time, and will allow air to escape through these gaps. Installing high-quality weatherstripping will help to prevent draughts. Another alternative is to replace the window with low-emissivity glass, which will help regulate indoor temperatures and will reduce the possibility of draughts.

One of the most effective ways to cut down on the draughts in your home is to use a draught excluder. These are typically fabric tubes which are filled with a type of filler. They can be placed on the top of your windowsill. These will help to block out cold air and keep your home warm and cosy!

Your windows made of upvc will continue to provide excellent insulation and security in your home by performing regular maintenance and repairs. It is crucial to recognise that windows last for a certain period of time and there may come the point when it's more efficient to replace them than repair them. If you are experiencing issues with your window made of upvc it is recommended to speak with an expert immediately.

Here's my website: https://www.repairmywindowsanddoors.co.uk/borehamwood-windowrepair/