Notes

An Guide To Replacing Upvc Window Handles In 2023
Replacing uPVC Window Handles

The replacement of window handles made of upvc is a simple job. It is essential to ensure that the new handle is fitted into the spindle cutout in the window mechanism.

If the steps below are followed properly the cockspur handle will fit most windows. The key is the step height of the handle.

What to Look For

A lot of windows in the UK are fitted with uPVC handles and, over time, they will begin to show signs of wear and wear and tear. The window handle can become loose or difficult-to-operate when this happens. Anyone who is proficient using a basic hand tool can complete this relatively simple job.

The first step is to ensure that the handle is securely fixed to the frame of the window and in its open position. The next step is to find the screws or pins that secure the handle. They are usually on the inside of the handle. They can be removed with a screwdriver or pliers.

When the handle has become loose, gently pull it away from its hinges. Then, you will need to locate a replacement handle in the same size and style. This can be done in a DIY store or online. The process should take only five minutes, and you will need a screwdriver is all you need.

When replacing the handle on a uPVC handle It is crucial to consider the step height. This is the distance from the base of the handle to the point at which it rests on the window frame. This is a standard measurement, and you should verify the height of the step before purchasing a replacement handle.

Depending on the kind of handle you choose There are various sizes to choose from. Inline handles for uPVC windows usually feature lug centers of 31mm There are also cockspur handle types that have 43mm centres. Tilt and turn handles are commonly found on windows made of uPVC and they come with a unique design that allows windows to be tilted for ventilation and turned to open the window fully.

The most common breakage in uPVC handles is that they crack inside instead of breaking off from the base section. This makes it difficult to open. It is important to make sure that any replacement handle is fitted with the same spindle as the original one.

Remove the old handle

If your window handles are damaged or incorrectly fitted, they can cause double-glazed windows to close and open incorrectly. They may even become stuck. There are a myriad of reasons like general wear and tear, or corrosion of the handle. In these situations it is essential to replace the upvc window handle as promptly as you can to avoid further damage or loss of functionality.

When replacing the handles on windows made of upvc it is recommended to remove the old handles from the window. To do this, start by getting rid of the screw that is covered when the handle is in the closed position. This should reveal another screw and once removed, you can then begin to take off the handle itself. It is a good idea to make use of an electric screwdriver for this as it will make the task easier and quicker.


Be aware that screws could be hidden beneath caps made of plastic. It is recommended to remove the covers with a Stanley knife. Once the old handle is removed, take a look at the square cut out on the base of the handle to make sure that the new window lock handles will work with it. This is crucial as you'll need to determine the length of the spindle of the old handle to make sure it matches the size of the window mechanism and handle spindle cut out.

There are three kinds of upvc handles: Espag handles with a central screw that can be turned right or left and Cranked handles that have two screws, and Spade handles which have arms that are flat and can be used on either side of the window made of upvc. It is easy to replace the handle once you've found one that is suitable. Just screw it into the frame, and ensure that the spindle is properly inserted into the lock mechanism. After that, it should be tightened to the window frame, and your new window handles made of upvc must be secure.

Take a measurement of the Spindle

If you need to replace a Upvc handle that has fallen, it's likely that the spindle that holds it in place is damaged or loose. In some instances, it can be fixed using a screw or pin to tighten it. In certain situations, it may be necessary to replace the handle. There are a variety of handles made from upvc. There are three kinds of handles: inline espagnolette tilt-and-turn, and cockspur. Each handle type has its own method for installing and replacing the handle.

It is crucial to measure the handle prior to purchasing a replacement. This will ensure that the new handle is of the correct size and will fit correctly within the window. Fortunately, all handles adhere to industry standards for sizing, so it's quite easy to locate the correct size.

To determine the size of your handle first, remove it from the window by turning it to the open position. You should be able to determine the dimensions of the pin or screw that secures the handle. Then, use the ruler or tape measure to determine the length of the spindle. Once you know the length of the spindle you can purchase a replacement spindle that is the same length.

The step height of a upvc window handle is another factor to take into consideration when you are buying a replacement. The step height is the distance from the base of the handle until where it sits on the frame. It is typically around 21mm or 9mm in aluminum and uPVC. To ensure that the new handle is suitable the gap, drop something in the gap to check how far it extends before meeting an obstruction.

door handles come with different backsets depending on what style of window you install them in. Inline the espag handle heights range from 43mm from centre to center (two fixing points). Cockspur handles however, have different backset heights according to the style of the window they are in. This is due to the fact that they have an extension spur that extends from the handle and is secured over a cockspur wedge striker.

Install the new handle

Once you've selected the new handle, make sure it is aligned with the screw holes on the door. Then, secure it with the screws provided. Install the latch lever in similar fashion to the main handle in the event that you are replacing the door handle. After that, attach the door trim to conceal the mounting screws and close off your project.

Tip: To remove the head made of metal from the wooden wedge make sure the handle is held so that its longer end is resting on the floor and use a hammer to tap the thin end of the handle. Be careful not to scratch the handle or spindle.

My Website: https://www.repairmywindowsanddoors.co.uk/beaconsfield-windowrepair/