Notes

15 Secretly Funny People Working In Suzuki Jimny Replacement Key
Suzuki Motorcycle Key Replacement

If you're looking to replace the Suzuki motorcycle key on your motorcycle it is important to ensure your locksmith is accustomed to this type of work. This is because traditional motorbike keys can be hard to work with.

Before suzuki swift car key cut a key, most locksmiths require proof of ownership. This could be your registration or bill, or a picture ID.

Ignition Cylinder Replacement

The ignition cylinder is the glue that holds everything together. The ignition cylinder is a circular silver-shafted cylinder into which you can insert the key. The cylinder has an electrical connector that connects to relay switches which supply the power to various motorcycle systems. If the cylinder is not working properly, you may observe that your vehicle is not starting or the key will not turn in the switch.

If you have a classic motorcycle key with a metallic blade, you could just get an extra cut by your local locksmith. They can make an identical key by using the code that you have from your current one.

In the event that your key isn't turning at the switch or if it snaps inside the lock, you will have to replace the ignition cylinder. This procedure is much more difficult and requires the assistance of a professional. Calling a local locksmith to make a new Suzuki bike key on the spot is the most secure option.

To replace the cylinder, you will need to remove the old one and clean it out. Then you will need to locate a key diagram on paper or template that shows all the tumblers that are on the cylinder. Once you've completed this, you will be able to remove each tumbler and then place it on the corresponding location on your paper key diagram.

Ignition Switch Replacement

Ignition switches are stuck for various reasons, but the most common is due to the use of wet oil lubricants like WD-40. These lubricants may temporarily fix the issue however they could cause problems in the future, as they attract dirt which can eventually jam the ignition switch, causing more issues starting your motorcycle. Dry graphite can be used instead of wet oil lubricants. Place the tip on the ignition switch and rub the graphite area slowly so that the powdered material falls into the opening. Continue this process until a decent amount of graphite falls into the switch opening.

You'll need to take your cylinder code to a locksmith. The majority of locksmiths can do this for you, but there are some that cannot. You'll have to look around to find one that can take care of this.

Once you have figured out the cylinder code, you are able to replace the ignition switch or at a minimum, take off the triple clamp on the top. It's a simple procedure and can be completed at home with the tools you already have in your garage. After the ignition switch has been removed you can replace it with a new ignition cylinder. Then, you can re-install the entire upper triple clamp. Be sure to select a quality lock set for your bike.

Ignition Wire Replacement

You'll need to find a solution if have lost or broken your motorcycle key, leaving a piece of it in the ignition. There are a few ways to get your key replaced with some options more expensive than other. If you are able to locate your cylinder's code, you can bring it to a locksmith, and have them cut a new key for you. This isn't possible for older motorcycles, or when the cylinder codes have been altered.

Another option is to take the ignition key to your local dealer. If you have a VIN number, they will be able to design you keys, however it will cost more. You can also try calling your local locksmith and asking if they create motorcycle keys. It is advisable to call prior to bringing your bike in as some locksmiths may not have the proper tools or have the necessary knowledge regarding motorcycle locks.


If you have a spare key you keep in a safe location, you can use this to start your motorcycle. Keep this key in a safe place to keep it safe from theft. It is also recommended to keep a spare key in case you lose your initial one or if it becomes damaged.

Keyless Entry System Replacement

Motorcycles are enjoyable to ride and provide a lot of freedom. They are susceptible to the same issues as cars and trucks. If you lose your keys or part of the key has broken off in the ignition, you'll want to find an experienced locksmith who has worked with key replacement for motorcycles. These experts can help you get back on the road as fast as is possible.

Keep a spare key for your motorcycle in your possession to ensure you don't lose yours. You can do this by placing the keys in an place where it is secure from being disturbed or moved. This could be in an apron, a basket or even a drawer that isn't used often. It's crucial to teach your children and family members to take care of this space.

You can also purchase a spare key from your dealer or bike shop. These are typically more expensive than a locksmith however they will be capable of creating the key you need. They will need the code from your ignition cylinder. The code is found on the silver shaft, where you put your key.

Most locksmiths can make keys for your Suzuki motorbike. However, the process is a little different from traditional cars and trucks. Motorcycle keys are more complicated because they contain electronic transponder technology that lets them start your vehicle. This makes them harder to duplicate than the typical house or car key.

Read More: https://www.g28carkeys.co.uk/suzuki-car-key-replacements-near-me/