Notes

14 Questions You're Afraid To Ask About Double Glazing Door Lock Repairs
Double Glazing Door Lock Repairs

Are you experiencing issues with your uPVC door or window mechanism faulty? Maybe the handles on your uPVC windows or doors are not aligned properly or are difficult to use.

You will lose energy if your double-glazed doors don't perform as they should. This increases the likelihood of burglaries. Owen the Locksmith can repair your door lock at a reasonable price.

Snapped Key

It can be quite frustrating when a key gets stuck inside a lock. It also poses an issue for security, since the door may not be locked and make you open to intrusion. There are Read More On this page of quick fixes you can try to fix the problem and make your door work again.

Keep calm. If you panic you may end up pushing the broken key further into the lock.

Then spray WD-40 or another penetrating oil into the lock to make the broken piece slide out more easily. You can also use a screwdriver to break any pieces that are stuck. If you have a chunk of the key that's stuck out then grab it using a paperclip or another thin metal object and pull it. Both methods work, but be careful not to push the damaged key further into the keyway.

Some paperclips come with grooved edges that can be used as hook extractors. Jigsaw blades can also work well for this. If you don't have any of these you can bend a hook with needle-nosed pliers. Finally, you can use a pair of tweezers grab and remove the remaining pieces of broken keys.

If you are unable to remove the broken key piece Use a lock deicer. It's usually available at all hardware stores. It works by freezing any moisture or ice that may be in the lock.

If none of these solutions seem to work, it could be time to call a locksmith. The experts at Fitlocks can quickly fix issues such as broken handles and snapped keys with uPVC locks and door mechanisms. They can also alter your double glazing door mechanisms to allow them to operate more easily. Book a double glazing repair via our website or give us a call to discuss your requirements.

Broken Cylinder

A broken cylinder can pose a major security risk. A locksmith professional can fix the cylinder. To fix the cylinder, locksmiths will need to tap it. This can be done with a hammer or other tool. However, the most effective method is to employ a wire or long match. Position the match or the wire end near the keyway. The locksmith can strike the lock and break it open. This is more secure than using the hammer, which could harm the lock.

Overheating is the primary cause of cylinder heads cracking. This can happen when the block and the cylinder head are made of different metals such as cast-iron and aluminium. When the different metals are heated and cool at different rates, it may create hotspots locally that expand faster than the rest of the cylinder head, leading to cracks.

Corrosion is a different cause of fractures in cylinders. If the cylinder block and head are not maintained correctly, they can be corroded or rust and cause them to expand faster than expected. This can cause cracks over time.

If your uPVC window or door lock is rigid and requires more pressure to turn it could be due to a variety of reasons. This issue could result from a defective locking mechanism, or misalignment as well as a worn-out handle.

It is a quick and affordable fix that the majority of double glazing owners can accomplish. A professional locksmith can usually solve the issue within one hour of arriving at your property. They can replace the locking mechanisms, or change the window handles and change the gearboxes, based on your particular requirements. A professional locksmith will be able to advise you on the most cost-effective solutions for your home. They can also suggest upgrades to 3 Star security TS007 euro cylinders that will provide an extra layer of security against burglars. This is a small price to pay for the security that comes from knowing your uPVC doors are safe.

Broken Handle

It's not a surprise that window handle locks may break. They are equipped with complex mechanisms that wear out over time. It can be difficult to determine the cause of a broken window handle lock and fix it correctly.

Repairing your damaged handle, whether it's the internal latch or the locking mechanism, will improve the security of your uPVC door and reduce the risk of draughts. Incorrectly repairing or replacing your handle can be expensive and could damage the door's frame and lock, so it's worth taking the time to do it correctly.

Screwdriver Open the window, loosen the screw holding the handle. double glazing repairs near me should be on the inside of the backplate, usually hidden by an eye-catching cap to conceal it for aesthetic reasons. Be sure to not lose any of the internal components inside the handle, such as the levers or plates on the opposite side of the spindle. Ideally, keep them in the same order so you can replace them again when needed.

Next, turn the handle so it's at 90 degrees towards the window frame. Then, loosen the screw on the back of the handle which holds it to the internal spindle using a second screwdriver. Once the screw is loose, take the handle off and take the broken spindle out. Replace it with a new one, making sure that it is the same length as the old one (you can typically find these online or in hardware stores) and then securely screw it into the correct position. Do not overtighten the screw as this could damage the handle and the window frame.

Make sure the new handle is installed, then close and test the handle. The hope is that it will function smoothly and you'll be able to unlock your window.


Don't forget to double-check that your uPVC window is shut correctly while you're working with the handle. If they aren't closing correctly, you could encounter damp or draughts in your home. It could also affect the energy efficiency of your home. Core Sash Windows is a local window company that can adjust the hinges on the frames of your windows to ensure that they shut correctly.

Broken Spindle

It is usually the case that the spindle in a handle breaks rather than the handle itself. This is especially common with uPVC tilt-and-turn windows. These windows require a handle that acts as a locking device in the frame of the window. The handle is connected to a central rod that triggers the locks that are shaped like mushrooms and secure into the frame of the window keep. If the dead latch mechanism fails to open after the handle is turned, it is most likely the spindle has been damaged. This could be a frustrating problem.

Fortunately there are options to rectify this issue. A reputable locksmith can quickly and effectively fix this problem. A reputable locksmith will be able disassemble the window's handle using a tool that removes the wheel part that houses the spindle. This is done without damage to the handle or the window frame.

After the wheel has been removed, the technician will examine the spindle to determine what caused it to break. This involves breaking the spindle into its individual components and carefully observing their general condition, as in addition to any specific areas of wear or damage. This process is typically performed in a clean environment by skilled technicians.

The next step is to clean the damaged spindle. This will remove any debris or dirt that might be preventing it from working normally. Read More On this page could be repaired or replaced. If it is being replaced the technician can take an identical dowel size to the one used in the first and drill mating holes into both pieces of the spindle. This ensures that the new spindle has precisely matched to the handle.

If the spindle that is damaged is beyond repair, it may be required to replace it completely. Home centres sell generic replacements but If the style of your window is rare then it is necessary to contact a wood worker or cabinet maker who can duplicate the exact model for you. Once the spindle has been installed, it is fixed to the handle. Line up the screw holes on the handle with the screws that are already in the frame. Once the new handle is firmly installed, you are now ready to operate your uPVC window.

Here's my website: https://click4r.com/posts/g/13783757/