Notes

Fiat 500 Keys Explained In Fewer Than 140 Characters
Fiat Panda Key Fob Replacement

Fiat Panda keyfobs are equipped with a transponder, which sends an electronic signal from the fob to the car that allows it to unlock doors or start the motor. However, the key fob may not function due to a variety of reasons.

The most common cause of key fob failure is the battery of the coin is dead. Other causes include water damage malfunctioning receiver modules and signal interference.

Dead Coin Battery

Replace the battery if your key fob has died. Choose a new button battery with the same size, voltage, and specification as the original.


If the key fob was exposed to water, like a splash of rain or salt water at the beach, it needs to be cleaned before it is able to be used again. A paper towel that has been soaked in isopropyl alcohol or electronic cleaner will do the trick.

If the key fob isn't working even though it is not exposed to water it could be due to a problem in the receiver module or internal electronic chip. In these situations it is possible that reprogramming the key fob using an OBDII scanner might aid.

Water Damage

You might have water damage to your key fob if it was submerged in a puddle, pool or washing machine. It's usually possible to fix it by taking the batteries off and cleaning the circuit board using rubbing alcohol. It's best to allow the device to completely dry before installing the battery.

You could have a damaged module when your key fob ceases working after replacing the battery or replacing it with. You can find the instructions for changing the programming of most remote keys on YouTube or in the owner's manual. You can also try resetting the car's onboard computer by using the OBDII scan tool.

Faulty Receiver Module

The key fob has an electronic chip that communicates with the vehicle's system. This chip will stop sending and receiving signals to the car if it becomes damaged. This can be caused by dropping the key fob or by water exposure. If the key fob is not working after exposure to water it could be possible to repair it by cleaning the chip using isopropyl alcohol or an electronic cleaner.

If the key fob is still unable to not respond after cleaning it there is a good chance that the module is faulty and will require to be replaced. A malfunctioning receiver could cause the key to cease to function. This is usually caused by electromagnetic interference.

Faulty electronic chip

The electronic chip inside your key fob plays a crucial function in the anti-theft security system of your vehicle. It sends a message to the immobiliser in your car to inform it whether the key is genuine. Your car will not start if the chip is damaged.

A damaged chip could be caused by interference from objects, bad weather or transmitters located near your vehicle. In this scenario, a new fob will be needed.

Contacts with the battery may be damaged.

The battery contacts of the key fob are delicate and could be damaged with hard usage. If they are bent, or damaged, the fob will not send any signals to receiver modules in the vehicle.

Modern fobs are equipped with rubber seals that keep out water. A splash of water or light rain should be fine however, submerging them in saltwater could harm the electronic chip.

The key fob comes with an embedded chip that communicates to the immobilizer system of the vehicle to start it. This system uses crypto coding systems in the latest vehicles and the older red key system in older models. The chip must be replaced if it's defective.

Poor 12 Volt Battery

A defective battery can cause the key fob to function. When this occurs the car's computer will not be able to recognize that the remote is inside the vehicle.

Before you replace the battery, test it by using a the voltmeter to determine its capacity. A fully charged battery should read 12.6 volts. If the reading drops significantly, it is time to replace the battery.

Put an electrical load for a short time on the battery to determine its capacity. This will take away 1% of the surface charges. Then take another measurement of the voltage. The longer the battery can hold its voltage more effectively, the greater its capacity. Ideal is to hold close to 12 volts over several minutes.

fiat key cover is the most common reason for the key fob not sending signals to the car. This issue can be fixed by replacing the battery. It is crucial to buy an identical battery dimensions and voltage as the original.

Fobs are not indestructible and can be damaged by a lot. The battery buttons and contacts are brittle and can be bent or broken by rough use.

A signal may also be interrupted by other transmitters or objects which use the same frequency. For instance, a lighting control panel near your home may send interference on the same bandwidth that key fobs utilize. This could cause interference with your car's remote control.

Incorrect OBDII Scan Tool

There are a number of reasons why a scanner could not work. Some are more complicated than others.

Professional scan tools enable a mechanic observe the car's network, and run various self-tests. These tools can save time, but they are costly and not accessible to most DIYers.

If your OBD2 scanner doesn't work Check the voltage on terminal 16 (scan tool power) and terminal 4 (chassis ground). If all is fine the fuse could have ruptured. This is one of the most frequent causes of failures in the scan tool. It is usually easy to fix the issue by replacing the fuse that has blown.

Read More: https://www.thekeylab.co.uk/fiat-car-keys/