Notes

11 Ways To Completely Redesign Your Boarding Up A Door
How to Go About Boarding Up a Door

Protecting investment properties that are vacant from the elements is feasible by board up a door. While it may not prevent all destruction, it can help avoid some of the problems that can arise from severe storms.

The boarding of doors and windows will also discourage trespassers and vandals. However, it can be expensive and time-consuming to install plywood boards over the openings on a house.

Measure the Door

The first thing you'll need is tape measure. You might want to keep a ladder or chair close to hand in case you need to see more clearly the top of the frame. If you must make use of these tools, be sure to wear gloves and goggles.

Start by measuring the door's width. You can do this by running an x-ray measure horizontally across the door. Be sure to eliminate any additional door parts such as a door sweep, from the measurement. Then, determine the height measurement by measuring up from the floor to the sill plate or lintel. It is important to take measurements in multiple locations, particularly when measuring doors older than they may not be an exact rectangular shape. If the measurements are different take the largest number.

You'll have to determine the size of the frame once you've determined the length and width. Ideally it should be 2'' larger than the door and 1 2'' higher. This will allow you enough space to shim the door and frame to fit.

It's a great idea to remove the casing or trim around the jambs of the door to observe the studs. This will help you determine the exact measurement of the gap between the studs and the frame.

After you have removed the trim, measure the width of your door frame using a tape measure. The frame should be measured at three different locations and then use the most compact measurement. Also, you should measure the height of the frame from the top to the bottom on both sides, and use the most compact measurement as the height of your door.

If you're having difficulty with the measurements, you should get a professional to your home and take the measurement. They'll inform you of the size and type of door you'll need and how to prepare your frame for a replacement door.

Plywood can be cut into pieces

A door frame is generally comprised of a set of thin boards or studs that create a hollow space around the door. Two hinges are attached to the studs, and they hold the door in place. This means that if you want to restore the door, it is important to remove the door from its hinges over the course of a few days. Placing plywood into the door opening is a simple method to enclose the door and keep insects from gaining entry into the home. This is easy to do without having to screw or nail the plywood to the door frame.

Plywood is a breeze to work with, cheap and looks beautiful once completed. This makes it the ideal material to provide temporary solutions to an issue that requires the removal of an existing door and refinishing or installing a new one. It is also useful to secure the opening in an area that is being renovated, like an unfinished basement, or a construction site.

For a wall constructed of plywood, start by taking measurements of the width and height of the door opening. Note the measurements using a utility blade and a metal straight edge like the drywall or metal square. Then, draw a chalk line across all the lines you have marked to indicate where you need to cut. Finally utilize circular saws to cut the plywood into a size.

It is important to protect both your ears and eyes when cutting plywood. Wear protective goggles or earplugs if possible. Additionally, it is crucial to use a knife with a lot of teeth that cut quickly and with less tear-out. Utilize a small piece of wood to guide the blade. Hold it a hair's breadth away from the line you are cutting.

An effective way to hold the plywood in place without gluing it to the studs is by fixing braces that are short at each end. Put one brace side that is inside and the other one on the outside of the door. Then, place the deck screws in each of the holes, and tighten them using an open-end wrench.

Fasten the Plywood

It's now time to connect the panel to the frame once you have the plywood sheet cut to the correct size and the holes to attach the rails and stiles of the door frame are predrilled. This is a straightforward project that doesn't require advanced carpentry skills as long as you have the right tools and follow the correct procedure.


Begin by putting up a table near the doorway, with two sawhorses and 2-by-4 framing lumber at each end of the table. Use the marks made during the measurement procedure to guide you in cutting the plywood. Score the lines with a utility knife and a drywall square or other metal straight edge. boarding up a doorway will serve as a guide to the saw blade, and prevent splintering of the plywood when you cut it.

Wear eye protection and use a circular table saw with a blade that has a fine-toothed edge to cut along the score line. Sand the edges of the panels with 120-grit paper to smooth it out and remove any burrs. After sanding apply a wood sealer and allow it to dry according to the manufacturer's instructions.

Install the hinges onto the door frame. If you are using a T hinge, you need to drill holes in the outside of the door for the straps of the hinges. Then, screw the outside hinge to the frame with a screwdriver. Repeat the same procedure on the inside of the door for the remaining hinges, being cautious not to tighten too much on any of them, or the door will shift.

If you have only a single hinged outside door it is possible to make it easier for the latch to close by putting an electrical wire through the loops on the outside hinges. Fold a short piece to tie wire in half, and then fish it through the two holes on the outside of the door. Then, twist the wires together and lock the door.

Install the Plywood

Based on the measurements you have taken using the measurements you took, put the plywood in the door opening. Change the frame's header (top) and the sill. Utilize a level to make sure there's no slop in the header or sill. If it's not perfect, place another shim where it is needed and continue the process until the sill and header are even.

After the plywood is in place, fix it using the stainless-steel hinge bolts and wingscrews. Use a screwgun equipped with an attachment for hex heads to prevent removing the heads of the screws.

While you're at it, If your home was constructed with studs that extend through the doorway's height, drill hanger bolts through the plywood and into the framing studs. This is a simpler task than cutting the hole using a saw for drywall.

After installing the plywood, measure the width and height of your door opening. If needed, trim the plywood bottom to fit the height of your door frame. Cut two pieces of framing lumber 1-by-6 as braces for the upper and lower edges. Cut along the lines drawn on your plywood using a circular blade with fine-toothed teeth. Wear eye protection. Splinters can be removed from the cuts by using a sanding device.

After you have placed the braces After you have placed the braces, use two pairs 2-inch finishing nail to attach each brace to the plywood. When you're finished counter-sink the heads of all nails. Cover the braces with a quality wood sealing product, like the wipe-on polyurethane made by Minwax.

If the door is too large it is possible to add decorative molding to fill in the space between your jamb and door, or you can resize your opening. In many instances, it's cheaper and simpler to just get a new door. It also eliminates any issues that you might have experienced with the door you originally purchased in the event that it was damaged or not suitable for the opening.

My Website: https://www.repairmywindowsanddoors.co.uk/nottingham-emergency-boarding-up-near-me/