Notes

Effect of individual papillomavirus throughout sinonasal cancer-a thorough review.
A structure with periodic sub-wavelength nanohole patterns interacts with incident light and causes extraordinary optical transmission (EOT), with metal nanoparticles leading to localized surface plasmon resonance (LSPR) phenomena. To explore the effects of metal nanoparticles (NPs), optical analysis is performed for metal NP layers with periodic hole patterns. Investigation of Ag NP arrangements and comparisons with metal film structures are presented. Ag NP structures with different hole configuration are explored. selleck chemical Also, the effects of increasing light incident angle are investigated for metal NP structures where EOT peak at 460 nm wavelength is observed. Moreover, electric field distributions at each transmittance peak wavelengths and optical noise are analyzed. As a result, optical characteristics of metal NP structures are obtained and differences in resonance at each wavelength are highlighted.In this paper, we report on the effects of the substrate thermal evaporation process rotation speed on the electroluminescence (EL) characteristics of organic light-emitting diodes (OLEDs). In general OLED research, rotational and angle tilted deposition are widely used to maintain uniformity. However, there have been few reports on the effects of this deposition method on film characteristics. We analyzed these effects and found that the film density and its refractive index showed remarkable changes as a function of substrate rotational speed during tilted deposition. The EL characteristics of the transport layer of fluorescent OLEDs were also significantly affected. We derived the OLED optimal thickness and refractive index from our calculations.In the research of organic light-emitting diodes (OLEDs), the OLEDs that are fabricated via conventional doping methods have complicated structures and fabrication processes. To overcome these limitations, the ultra-thin emission layer (EML) method, which adopts a simple structure has been effectively used in the research of OLEDs. However, studies on white color OLEDs (WOLEDs) fabricated using the ultra-thin EML method are scarce. In this paper, we report the results of color tuning for the realization of WOLEDs based on an ultra-thin EML structure. The WOLEDs were fabricated and evaluated based on a two-color dopant system (sky-blue dopant and yellow dopant). The fabricated WOLEDs exhibited color coordinates of the International Commission on Illumination (CIE) 1931 from (0.287, 0.436) to (0.486, 0.483) according to the thickness ratio of the two dopants. This result suggests that the WOLEDs color tuned with multi-color dopants can be fabricated based on the ultra-thin EML method, and the development of WOLEDs with high efficiency and stability can be attained in the future.Many studies on anti-bacterial/antiviral surfaces have been conducted to prevent epidemic spread worldwide. Several nanoparticles such as those composed of silver and copper are known to have antiviral properties. In this study, we developed copper oxide (CuO) nanoparticle-incorporated nanofibers to inactivate or remove viruses. The CuO nanoparticle-incorporated nanofiber was fabricated with a hydrophobic polymer-polyvinylpyrrolidone (PVP)-using electrospinning, and CuO nanoparticles were exposed from the PVP polymer surface by etching the nanofiber with oxygen plasma. The fabrication conditions of electrospinning and oxygen plasma etching were investigated by scanning electron microscopy (SEM), and field emission transmission electron microscopy (FETEM)/ energy dispersive spectrometry (EDS). H1N1 virus was utilized as the target sample and quantified by RT-qPCR. The antiviral efficacy of CuO nanoparticle-incorporated nanofibers was compared against bare CuO nanoparticles. Overall, 70% of the viruses were inactivated after CuO nanoparticle-incorporated nanofibers were incubated with 10² pfu/mL of H1N1 virus solution for 4 h. This indicates that the developed CuO nanoparticle-incorporated nanofibers have noticeable antiviral efficacy. As the developed CuO nanoparticle-incorporated nanofibers exerted promising antiviral effects against H1N1 virus, it is expected to benefit global health by preventing epidemic spread.The zirconia used in dental implants requires excellent mechanical and chemical properties such as high strength, high biological performance, corrosion resistance, and phase stability. In this study, after we prepared a highly fluidized solution of calcium phosphate, we fabricated a hydroxyapatite (HA) coating layer on a zirconia substrate using the sol-gel method to enhance its biocompatibility and bone-bonding ability. We dipped the zirconia substrate into the calcium phosphate sol to obtain the HA-coated film, which was dried at room temperature. The phase change and microstructural evolution were examined while the coating dried and during heat treatment. The biological activity of the coated and as-received substrates was evaluated using an in vitro experiment and the results were compared. The HA-coated film showed a highly dense and uniform layer structure, while its physical and biological properties depended on the starting substrate, coating times, and processing conditions.In this study, two types of carbon nanotubes were used as ophthalmic material, and hydrogel contact lenses were polymerized by adding two types of dispersants to effectively exert the functions of carbon nanotubes. The physical properties and surfaces of the ophthalmic hydrogel lenses prepared to confirm the functionality as a dispersant were compared and analyzed to find the utility as an ophthalmic lens material. For the polymerization, single-walled carbon nanotubes (SWCNTs), single-walled carbon nanotubes carboxylic acid functionalized (SWCCNTs), 2-hydroxyethyl methacrylate (HEMA), ethylene glycol dimethacrylate (EGDMA, a crosslinking agent), and azobisisobutyronitrile (AIBN, an initiator) was used. In addition, as a dispersant, PVP (polyvinylpyrrolidone) and BYK-111 were copolymerized. As a result of this study, PVP increased the water content and decreased refractive index regardless of the type of carbon, whereas BYK-111 did not show a significant difference in basic properties. Also, PVP gradually decreased breaking strength, while BYK-111 gradually increased breaking strength. BYK-111 effectively exerted the function of carbon nanotubes, and it was confirmed whether it was dispersed through TEM. Therefore, if carbon nanotubes are used as ophthalmic materials by utilizing BYK-111, it considered to be used as functional ophthalmic lens materials.Zirconia dental implants require excellent biocompatibility and high bonding strength. In this study, we attempted to fabricate biocompatible zirconia ceramics through surface modification by hydroxyapatite (HA) slurry coating. A hydroxyapatite slurry for spin coating was prepared using two sizes of hydroxyapatite particles. The hydroxyapatite slurry was obtained by adjusting the solid loading, pH range, and dispersant content. The surface roughness of the HA-coated layers on the zirconia substrate depended on the change in microstructural evolution and coating thickness. With repeated coating, the coating thickness gradually increased for both small and large particles. The specimen with two coatings had the maximum surface roughness but displayed different values depending on the size of the HA particles. High surface roughness (Ra; 0.49 μm) could be obtained from the slurry of small particles compared with that of the large particles (Ra; 0.35 μm). During a 14 days in vitro experiment in SBF solution at pH 7.4, no changes were observed in the surface microstructure of the HA coating layer on the zirconia substrate.Zirconia ceramics has a bioinert property with low bioactivity. So, it is necessary to improve its low bioactivity by the surface modification using effective coating methods. In this study, we fabricated the hydroxyapatite-coated zirconia substrate by room temperature spray processing to improve the bioactivity of the zirconia implant and investigated its coating effect on the biological performance of zirconia substrate via an in vitro test in simulated body fluid (SBF) solution. Before the room temperature spray coating was completed, size-controlled hydroxyapatite powder that had an average size of 4.5 μm, was obtained by the calcination and milling of a commercial powder. By controlling the processing parameters, such as spraying distance, and deposition cycles, we fabricated homogeneous and dense hydroxyapatite coatings on zirconia substrate. Surface morphology, coating thickness, and microstructure were dependent on deposition cycles, and were related to surface roughness and bioactivity. Zirconia substrates with wave-patterned and roughened hydroxyapatite coatings demonstrated high bioactivity in their in vitro tests. Via the immersion test in an SBF solution, surface dissolution and new precipitates of hydroxyapatite were observed on coated zirconia substrate, indicating the degree of bioactivity.In this study, hydrophilic and biocompatible chitosan oligosaccharide lactate (COL)-coated ultra-small gadolinium oxide nanoparticles (NPs) were synthesized through a one-pot polyol method and characterized by various experimental techniques. The In Vitro cellular cytotoxicity assay indicated that the COL-coated gadolinium oxide NPs were non-toxic up to 500 μM Gd. In addition, their water proton spin relaxivities (i.e., r1 and r₂) were estimated to be 13.0 and 27.0 s-1mM-1, respectively, which are higher than those of commercial magnetic resonance imaging (MRI) contrast agents. The application potential of the solution sample as a T1 MRI contrast agent was demonstrated In Vitro by measuring map images in which dose-dependent contrast enhancements were observed.Parathyroid hormone (PTH) is a hormone that plays a critical role in bone remodeling because it regulates the calcium levels. Either higher or lower than normal range of PTH release can cause serious metabolic disorders such as hyperparathyroidism or hypoparathyroidism. Therefore, the demand of highly sensitive monitoring sensor of PTH is on the rise. However, due to its presence of small size and low concentration in serum, the monitoring of a small change of PTH level is extremely difficult. In this article, we suggested the fabrication of europium complex doped nanoparticles conjugated with PTH antibodies for the sensitive fluorescence monitoring of PTH. For the synthesis of europium complex, 4,4,4-trifluoro-1-(2-naphthyl)-1,3-butanedione (NTA) and trioctylphosphine oxide (TOPO) are used to encapsulate europium. The amphiphilic polymer, polyvinylpyrrolidone (PVP), was applied to hydrophobic europium complex, and then silica shell was synthesized on the complex. Using the europium complex doped silica nanoparticles, we could obtain approximately 4.24-fold enhanced fluorescence in low levels of PTH in PBS, when compared to the conventional enzyme-linked immunosorbent assay (ELISA). In addition, we could obtain the sensitive PTH immunoassay in PTH spiked serum with high selectivity.Stem-loop hairpin DNA probes have high hybridization specificity and unique selectivity to target molecules such as DNA and small molecules. DNA-templated silver nanoclusters (DNA-AgNCs) has been widely used to detect biomolecules of interest due to the photostable, bright, and efficient methods. In this study, we measured fluorescence emission of hairpin DNA upon hybridization with cDNA and mutant cDNA (cDNA-1) or mutant cDNA containing mismatched bases in the stem region (cDNA-2). Fluorescence intensity of hairpin DNA-AgNCs in the presence of cDNA was 1.80 times higher than that of hairpin DNA-AgNCs alone, but decreased to 66% in the presence of cDNA-1 containing mismatched base corresponding to the hairpin stem region. This study demonstrated that fluorescence intensities of hairpin DNA-AgNCs were dependent on hybridization with either wild-type and mutant cDNAs.
Homepage: https://www.selleckchem.com/products/srpin340.html