Notes

10 Things People Hate About Boarding Up A Door
How to Go About Boarding Up a Door

Protecting investment properties that are vacant from the elements is possible by board up a door. It may not prevent all damage, but it can help to prevent some of the issues that are associated with severe storms.

The boarding up of windows and doors can also deter burglars and vandals. Installing plywood boards over openings could be time-consuming and costly.

Measure the Door

The first thing you'll need is a tape measure. It is also advisable to keep a ladder or chair handy for when you need to get a better look at the top of the frame. If you must make use of these tools, be sure to wear gloves and goggles.

Start by measuring the width of the door. This can be accomplished by running the tape measure horizontally across the door. Be sure to remove all other parts of the door, such as a sweep, before measuring. Then, take the height measurement by measuring from the floor to the existing sill plate or lintel. It is crucial to measure in multiple locations particularly with older doors, since they are not always an exact rectangle. If the measurements are different take the largest number.

After you've taken the width and height measurements, you'll need to determine what size boarding you need for the frame. It should be at least 2'' wider and 1'' higher than the door. 2'' higher. This will allow plenty of space to move the frame and door into place.

It's a good idea to remove the casing or trim around the jambs of your door to see the studs. This will help you to determine the exact measurement of the gap between studs and the frame.

After removing the trim, measure the width of the door frame using the tape measure. Measure the frame at three different places and then use the most compact measurement. It is also important to determine the height of the frame from top to bottom, on both sides. Use the shortest measurement to determine your door's width.

If you're having issues with these measurements It's a good idea at this point to consult a professional and have them come out to your house to take the measurements for you. They will be able to tell you exactly what type and size of door you require and how to prepare the frame for the new door.

Cut the Plywood


A door frame is typically composed of a series of thin boards or studs which create a hollow space surrounding the door. Two hinges are attached to the studs and hold the door in its place. This means that if you need to finish the door, it is essential to take the hinges off the door overnight. To prevent insects from entering your home and to secure the door's opening, a simple method for boarding the door is to put plywood into the opening. This is easy to do without having to screw or nail the plywood to the door frame.

Plywood is easy to work with, affordable and looks great once it's finished. It is the ideal material to make a temporary solution for situations where you're required to remove the door you have in place to refinish or install the new one. It can also be used to protect the opening of a room that is being renovated, such as a basement or construction site.

To build a wall made of plywood begin by taking measurements of the width and height of the door opening. Make notes using an utility blade and a metal straight edge like a drywall or a square. Then, you can snap an outline of chalk across each line to indicate where you want to cut. Then you can use circular saws to cut out the plywood into a size.

It is essential to protect both your eyes and ears when cutting plywood. Wear protective goggles or earplugs when you can. Additionally, it is important to use a blade that has a wide range of teeth that will cut quickly and with minimal tear-out. To reduce the chances of breaking pieces of wood from the edges of your cut using a small piece of wood as a template to guide the blade and keep it at a distance of just a hair's width away from the mark when cutting.

boarding up company to keep the plywood in place without fixing it to the studs is by fixing two braces at each end. Put one brace on the side that is inside and the other one on the outside of the door. Place a 1-1/2-inch deck screws in each hole, and then tighten using an open-end ratchet.

Secure the Plywood

Once you have a sheet of plywood cut to the appropriate size and with the holes for stiles and rails predrilled and ready to attach the panel to the frame. This is a simple project that doesn't require a lot of advanced carpentry skills as long as you have the right tools and follow the proper procedure.

Set up a table in the entrance with two sawhorses on each end, and framing lumber 2x4s. Lay the full sheet of plywood flat on top of the sawhorses, using the marks from the measurement process to guide you to cut. Use a utility blade and a straight edge of metal to score the lines. This will create an outline for the saw blade and help keep the wood from splintering when cutting the plywood.

Wear eye protection and cut along the lines of scoring using a circular or table saw fitted with a fine-tooth blade. Sand the edges of the panel using 120-grit paper to smooth it out and eliminate any burrs. After sanding the plywood panels apply a wood sealer and let it dry in accordance with the manufacturer's guidelines.

Install the hinges onto the frame of your door. If you're using a T-hinge, drill holes on the outside face of your door for the straps of the hinges. Then, attach the hinge's outside edge to the frame with a screwdriver. Repeat the procedure on the inside of the door for all of the hinges remaining, being careful not to overtighten any of them, or the panel may shift.

If you are using one outside hinged door, you can make it easier to close and lock with a chain latch by putting a piece of wire through the loops on the hinges outside. Fold a small piece of connect wires in half and then fish it through the two holes on the outside of the door. Then twist the wires and lock the door.

Install the Plywood

With the measurements you made using the measurements you took, put the plywood in the door opening. Move the header of the frame (top) and the sill. Use a level to be sure there's not any slop in the header or sill. If it's not quite right you can put another shim where needed and continue this process until you get the sill and header to be plumb.

Once the plywood is in place, secure it with the stainless-steel hinge bolts and wingnuts. Make use of a screwgun that has a hex head attachment to prevent removing the heads of the screws.

If your house has studs running the length of your doorway, you could drill hanger bolts into each of the framing members. This is a far easier task than cutting the hole using the drywall saw.

After installing the plywood measure the width and the height of the door opening. If necessary, cut your plywood bottom to fit the height of the door frame. Cut two pieces of framing wood 1-by-6 as braces for the lower and upper ends. Wear eye protection and cut along the lines drawn on the plywood using circular saws fitted with a fine-toothed knife. Splinters can be removed from the cuts by using a sanding device.

After you've placed the braces, use two pairs of finishing nails that measure 2 inches to join each brace to the plywood. Counter sink all nail heads when you're done. Cover the braces with a good wood sealing product, like the wipe-on polyurethane by Minwax.

If the door is too big for the doorway, you can put in an ornamental molding to fill in the gap between the door and jamb or you can reduce the size of the opening. In many cases it's cheaper and easier to simply buy a new door. This can also alleviate any problems that you might have faced with the original door, if it was damaged and didn't suitable for the opening.

Homepage: https://www.repairmywindowsanddoors.co.uk/dover-emergency-boarding-up-near-me/