Notes

What's Everyone Talking About Boarding Up Windows And Doors Today
Boarding Up Windows and Doors Before a Storm Hits

The act of boarding up your doors and windows before the storm hits can offer the protection you need against damage. To do this, you'll must have a few things in your desk.

Find the width and height of the window including the frame (not the trim or the masonry around the window). Note these measurements to ensure you don't forget them.

Preparation

It is always recommended to secure windows and doors before the storm or another natural disasters strike. This will stop property damage and reduce the loss of life. It requires lots of planning to build a board around windows. You will need to purchase and measure plywood boards and you must be aware of the specific dimensions of each window. Moreover, it takes time to cut the boards and install them properly. Fortunately it is possible to make the process made simpler by preparing as soon as you hear of a possible storm coming in your area. You can avoid stress in the last minute, and make it easier for both you and your staff.

Begin by listening to weather forecasters and following the guidelines set by your local government. The earlier you begin the process the better, since it allows you time to gather and store the necessary materials without feeling pressured by a fast-approaching storm. Depending on the severity of the imminent storm, you might require huge quantities of plywood to cover all your windows. To ensure you get the correct size, make use of a tape measure determine the height and width of each window opening. Make sure to include the framing or trim around each window, as well as any ledges with extended edges if they are necessary.

Next, calculate the dimensions of the sheets of plywood you require by dividing your window's total height and width by 2. If your window has a width of 16 inches, the thickness of each sheet is 8 inches. If your exterior is made of wood, drill pilot holes into the plywood sheet to ensure it is aligned with the window frame below. This will reduce splitting when you screw in the screws.

If you have a larger window than a single sheet of plywood is able to handle cut two sheets of plywood that are each half as large as the desired window. Then place them side by side on the wall. Then cut a piece of 2 by 4 in (5.1 by 10.2 cm) lumber to the length of the connecting edge of the plywood sheets and then place it over the seam. Then you can drive 2.25 in (5.7 cm) screws through the bracing and into the plywood sheet to join them together.

Materials

To ensure safety and security for security and safety, boarding up windows and doors should be done with only strong materials that will not break under pressure or splinter during high winds. Plywood is the most common material used to encase windows. It is easy to use, inexpensive, and easily available. Choose plywood that is of the exterior grade (CDX), as it is more durable and have fewer knots and warps. A stronger option is storm shutters, also known as hurricane shutters, which are installed over windows that are already in place to provide greater protection against shattered glass and inclement weather.

Once you've identified the location of the window openings, measure the width and height of each to determine the amount of plywood you'll require. Then you can use a power drill to create pilot holes into the plywood sheets at two-inch intervals around each window. Mark the walls with studs prior to attaching the plywood to ensure the boards are fastened securely. If your home has wood siding, look for nailheads that might indicate the location of studs. You can also use a drill to find the studs' locations. The screws should be driven into the framing, not into the trim or sheathing. A plywood panel that is attached to these materials alone could become a safety hazard during high winds.

If the size of your window is too large for a single sheet of plywood, cut two separate pieces which are each half the size you require. join them with 2 by 4 inch lumber. Label each plywood panel to let you know what window it will be covering.

To affix the plywood panels to the wall, make use of corrosion-resistant screws that are long enough to penetrate both the sheathing and the studs. To attach the plywood panels to the wall, use corrosion-resistant screws that are long enough to get through both the sheathing as well as the studs.

In addition to securing your windows, you should also install an "No Trespassing" sign on your property and consider installing polycarbonate security glazing like DefenseLite over your primary windows. These transparent shields are bonded to the existing glass and safeguard your doors and windows. They are virtually unbreakable and deter criminals from gaining entry into your home.

Installation

If you live in an area prone to hurricanes, or are planning to move to one, the best way to protect yourself is to board up your doors and windows before the possibility of a storm is afoot. This project can be completed quickly and efficiently, however only if the plywood sheets are measured, cut and labeled prior to the storm arrives.


You'll also need a few other tools, like drills (or nails and a hammer for those who don't own a power drill) as well as tape, a saw gloves, a level and a pair of safety glasses. It's an excellent idea for the plywood to be coated with sealant in order to make it waterproof.

Start by taking measurements of the width and height of each window opening, then cutting your plywood sheets so they fit inside the frames with an overlap of 4 inches on all sides. This is best done on the spot as you are more in control of the exact dimensions.

Utilize a circular or track saw to cut the boards to the proper size, and remember that you'll have to sand them down after they've been put in. Once you've put your boards in place, screw 3 inch stainless steel hanger bolts into the framing studs around each window. Use washers on each bolt and wing nuts to ensure they are secured. Make sure that each screw gets through the studs by at least 2 inches to ensure the board is strong enough to withstand high winds.

If boarding up windows service using concrete blocks, you can join the plywood using galvanized pan head screws which are driven into the edges of the panels to masonry or cinder block. You will also need to drill pilot holes into the masonry, and then screw corrosion-resistant screws into the holes. It's a project that can take anywhere from three to four hours per window, so it's essential to begin the process as soon as you hear that a hurricane warning has been issued. This will allow you time to finish the task before the storm hits.

Maintenance

You should be prepared to board up your windows and doors before the onset of a severe storm. This can help you avoid costly repairs and protect your property from further damage from wind, rain debris, flying debris and other factors that can impact the windows.

The right materials can make boarding up easier and quicker. The key is to precisely measure the dimensions of each window you have to cover. This will ensure that the plywood or OSB fits snugly and won't come off easily. If you're using plywood be sure to use exterior-grade sheets and consider adding an extra layer of protection.

Once you have the plywood or OSB measured, mark the spots where the screws will go into the board. Make use of a drill to drill holes at intervals of 12 inches into the plywood. You can then use hanger bolts to anchor the boards in a disaster situation. When the storm has passed and the local authorities have given the all-clear, take out the bolts but keep them in case of a need in the future.

The next step is to install the plywood panels over the windows. Be prepared to work in pairs. If you are using plywood, sand the edges to make them smooth so that they don't scratch paint or trim. Then, attach the plywood to the frame with screws that are corrosion-resistant that fit into the pilot holes. If your home has vinyl shingles on it, attach the plywood directly to the shingles and not to the wood framing.

A window that is boarded up can be used to discourage burglars. Burglars will target a building with a damaged window or one that is not secured. They're also more likely to attack a store that's been closed than one that isn't. This is something that business owners in retail must take seriously.

My Website: https://www.repairmywindowsanddoors.co.uk/west-bromwich-emergency-boarding-up-near-me/