Notes

A Boarding Up A Door Success Story You'll Never Be Able To
How to Go About Boarding Up a Door

Protecting vacant investment properties against the elements is attainable by board up a door. While it won't prevent all damage, it can avoid some of the issues that can arise from severe storms.

The boarding of doors and windows can also deter burglars and vandals. However, it can be expensive and time-consuming to set up plywood boards over the openings in a home.

Measure the Door

You'll require a tape measurement. You might want to keep a ladder or a chair close to hand in case you need an improved view of the top of the frame. Wear gloves and safety glasses if you have to use these tools.

Once you have the measuring tool, begin by taking the door width measurement. This can be done by running the tape measure horizontally across the door. Be sure to take out all additional parts of the door, like the sweep, when measuring. Then, take a measurement of the height by measuring from the floor to the sill or lintel. It is important to take measurements in multiple places, particularly when measuring older doors as they may not be a perfect rectangular shape. If the measurements differ, use the largest number.

You'll need to determine the size of the frame after having determined the length and width. It should be at a minimum 2 inches larger and 1'' higher than the door. 2'' higher. This will allow plenty of space to shim the frame and door into place.

It's a good idea to remove the casing or trim around the jambs of your door to be able to see the studs. This will allow you to take measurements of the exact gap between the frame's studs and the edge.

After you've removed your trim, you can determine the width of the frame of your door by running the tape measure across the entire frame in three places and using the smallest measurement to determine your door's width. You should also measure the frame's height from top to bottom, on both sides. Choose the shortest measurement to determine your door's width.

If you're having issues with the measurements, you should seek out a professional who will come to your home and take the measurement. They will be able to tell you exactly what kind of door and size you require and how to prepare the frame to accommodate a new door.

Plywood can be cut into pieces

A door frame is typically comprised of studs or boards that create a hollow space around the door. Two hinges are attached to the studs, and they hold a typical door in position. If you want to refinish doors, you'll have to take it off its hinges over night. To prevent insects from entering your home and to secure the door's opening, a quick and easy method for boarding doors is to place plywood into the opening. It is simple to do this without having to nail or screw the plywood to the frame of the door.

Plywood is cheap, easy to work with and looks fantastic when finished. It is the perfect material to use as a temporary fix for situations where you have to take down an existing door to refinish it or put in an entirely new one. It can also be used to secure the opening of a space being transformed, such as a basement or construction site.

Start by measuring the width of your door opening and its height. Mark the measurements with an utility knife and a straight edge of metal such as a drywall or a metal square. Then, snap an outline of chalk across each line to mark the area to cut. Then you can use a circular saw to cut the plywood into a size.

When cutting the plywood, it is essential to protect your ears and eyes. Wear protective goggles or earplugs if possible. Additionally, it is essential to choose a blade with a lot of teeth that can cut quickly and with minimal tear-out. Utilize a small piece of wood to guide the blade. Hold it about a hair's breadth away from the line you are cutting.

A great way to hold the plywood in place without gluing it to the studs is to attach two braces at each end. Set one brace inside and the other outside of the door. Then, position two 1-1/2-inch deck screws into each of the holes and tighten them using an open-end wrench.

Fix the Plywood

Once you have a sheet of plywood cut to the appropriate dimensions and with the holes for the door frame's rails and stiles already drilled, it is time to attach the panel to the frame. This is a relatively simple project that does not require a lot of carpentry expertise, provided you follow the correct procedure and use the right tools.

Set up a table in the doorway with two sawhorses on each end, and framing lumber 2x4s. Lay the entire sheet of plywood flat atop the sawhorses and use the marks made during the measurement process as a reference to cut. Cut the lines using a utility knife and a drywall square or any other metal straight edge. This will provide a guideline for the saw blade and prevent splintering when you cut the plywood.

Wear eye protection and use a circular or table saw with a fine-toothed blade to cut along the line of scoring. Then sand the edges the plywood panel with 120-grit sandpaper. This will smooth out the panels and remove any burrs that may have formed from the saw cuts. After sanding, apply a coat of wood sealer on the plywood panels and let dry as directed by the manufacturer.

Install repairmywindowsanddoors on the frame of the door. If you are using T hinges, make holes in the outside of the door to accommodate the straps of the hinges. Then, you can screw the hinge's outside edge to the frame using the screwdriver. Repeat the same procedure on the inside of the door for all of the hinges remaining, being careful not to overtighten any of them or the door will shift.

If you're using a single outside T-hinged door you can make it easier to close and lock with a chain latch by fishing a piece of wire through the loops of the outside hinges. Bend a piece of tie wire in half and fish it through each of the two holes on the exterior of the door. Then connect the wires to pull them tightly and secure the door.

Install the Plywood

Using the measurements you took and place the plywood into the door opening. Move the header (top) of the frame and the sill (bottom). Utilize a level to make sure there's no slop in either the header or sill. If it's not perfect then put a second shim in the place where you need it and repeat the process until you get the header and sill to be in a straight line.


Once the plywood has been put set, secure it with the stainless steel hinge bolts and wingscrews. Use a screwgun with an attachment for a hex head to avoid removing the heads of the screws.

If you live in a house with studs running along your doorway, it is possible to drill hanger bolts into each of the framing members. This is a lot easier than using a drywall cutting tool to create the hole.

After you have installed the plywood, measure the width and the height of the door opening. If necessary, cut your bottom of the plywood to match the height your door frame. Cut two pieces of framing lumber 1-by-6 to form braces for the upper and lower ends. Put on eye protection and cut along the lines drawn on the plywood using a circular saw fitted with a fine-toothed blade. Take any splinters out of the cuts by using an Sanding block.

After you have the braces in place attach each one to the plywood using a pair of 2-inch finishing nails. After you're done counter-sink the heads of all nails. Make sure to seal the braces and the plywood with a quality wood sealer, such as this wipe on polyurethane from Minwax.

If the door is too big for your doorway, you can put in a piece of decorative molding to fill in the space between the door and jamb or resize the opening. However, in many cases, it's cheaper and easier to simply find an alternative door. This can also alleviate any problems you may have experienced with the original door if it was damaged and could no fit for the opening.

Read More: https://www.repairmywindowsanddoors.co.uk/manchester-emergency-boarding-up-near-me/