Notes

Five Kia Picanto Key Fob Replacement Lessons From The Professionals
How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models comes with a keyless entry system built into. This key typically resembles an remote control, and can be changed by a new one purchased from a Kia dealer or a locksmith.

Key fobs might stop working due to a variety of reasons, including a dead coin battery, worn buttons, water damage, signal interference and a faulty receiver module. Here are some helpful tips on how you can get your Kia Sportage replacement key to work again.

How to replace kia sportage key or a smartkey?

No matter if your Kia comes with an intelligent key, remote key, push-to-start key, or a regular non-transponder steel key the battery in these keys will eventually require replacing. This is particularly the case if your car displays a message indicating that the remote or smart keys aren't powered.

It's a fairly simple process. To replace the battery on the keyfob, remove your mechanical key from the slot at the back of the fob. Then, pull the cover open. Inside the key fob, there will be an incredibly small screw that holds the battery in place. Utilizing a small screwdriver loosen the screw and pull out the old battery. Then, insert the new one and close the slit on the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock according to your expectations, then you're all set! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get chilly or when you need to do some errands in Brandon.

Note: Certain key fobs may need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of steel) don't require programming. If you're looking to reprogramme your key, it is necessary to record the key code number on the tag for the key code.

How do you replace the battery?

If the Kia key fob doesn't respond when you press the lock/unlock button, it is most likely that the battery is low. A weak battery could cause other issues, such as the check engine light flashing or the engine not running properly. Fortunately replacing the battery on the key fob is a simple DIY project that requires only a few tools.

Make sure that you shut off your vehicle and close all doors prior to beginning. Locate the small plastic piece that is on the bottom of your key fob and play with it until a metallic key slips out. This key can be put into the door's driver handle to unlock your car.

To replace the key fob battery, take off the rear cover and use a plastic pry bar tool to release the latch holding the black negative battery cable. Remove the old battery and orient the new one in a way that the "+" positive side faces you and the "negative" negative side is facing the fob's electronic contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid damaging or bending the contacts on the metal.

After the new battery has been installed, turn the key fob off and then turn it on in the ignition until the door locks. You can then test the Kia's Key fob again to make sure it is working correctly.

How do you replace a smart keys

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The difference is that the smart key has an incredibly small key blade in it, whereas the standard fob doesn't. Both key fobs come with an internal battery that will eventually require changing. This is a simple procedure which takes just two minutes.

Before you get started it is important to ensure that you're on a level surface with good lighting and that your Kia is turned off. Be aware that there are tiny pieces inside the fob that could be removed if not vigilant.

The first step is to find the small release button that is located on the back of the lower part of the fob. This will be either a circular button or rectangular slot. Once you press this, the mechanical key blade will come out and you can then open the key fob.

Once you have the key fob open and you are able to take off the old battery and replace it. The new battery is one called CR-2032 and can be bought from a local or online auto parts shop. After you've finished with the battery, you should be able to lock, unlock and start your vehicle using your key fob even if the engine isn't running!


How do I replace a mechanical key

The Kia keyfob can be a fantastic convenience that lets us lock or unlock our car simply by pressing the button. However, like all devices it will encounter issues at times. There are solutions to fix these problems and keep your key fobs running for the duration of.

A low or dead battery is one of the most common issues. This could cause your device to stop working or operate intermittently. If this is what you are experiencing you should replace the battery a new one.

If this doesn't solve the issue, use the flathead screwdriver that is standard to push the plastic casing of the fob open. Be cautious not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a new one.

Close and open the door with the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob and verify that it's working correctly. If the fob isn't working, call a dealer or locksmith to resolve the issue. Make sure they cut you an emergency key that functions in all the trunk and door cylinders, to avoid lockouts again.

Website: https://www.thekeylab.co.uk/kia-car-keys/