Notes

Why Kia Picanto Key Fob Replacement Could Be Your Next Big Obsession
How to Replace a Kia Sportage Replacement Key

The key in many Kia models has an entry system that is keyless into. The key functions like the remote control and can be exchanged by an Kia dealer.

Key fobs may stop working for a variety of reasons, such as the battery of the coin is dead worn buttons, water damage, signal interference and a faulty receiver module. Here are some suggestions to assist you in getting your Kia sportage replacement key working again.

How do you replace the remote key or smartkey

If your Kia comes with an intelligent key, remote key, push to start key, or a regular non-transponder steel key the battery in these keys will eventually require replacing. This is particularly true if the car displays a message telling that the smart or remote key has a low battery.

Luckily, it's an easy procedure. In order to replace the battery on the key fob, remove the mechanical key from the slit at the back of the key fob. You then need to remove the cover. Inside the key fob will be an incredibly small screw that holds the battery in the correct position. Take out the old battery by removing the screw with the help of a small screwdriver. Install the new battery and close the opening on the key fob.

Once the key fob has a fresh battery, test it by pressing the locks and unlock buttons. You're in good shape If the doors lock and unlock as you expect. You can now use the Kia's hands-free lock/unlock feature whenever your fingers get chilly or you need to go on errands around Brandon.

Note: replacement key for kia sportage The Key Lab (transponder chip or smart keys) might require their programming completed. This requires a programing machine that is available only to the locksmith in the automotive or dealer. Other keys (non transponder keys made of metal) are not required for programming. If your keys need to be programmed, you must know the key code number printed on the tag that identifies the key and save it in a secure location.

How do you replace a dead battery?

If the Kia key fob does not respond when you press the lock/unlock button, it is most likely that the battery is not fully charged. A low battery may cause other issues, such as the check engine light turning on or the engine not working correctly. It is quite simple to replace the key fob batteries with only a few simple tools.

Make sure that you shut off your vehicle and close the doors before you begin. Locate the small plastic piece that is on the bottom of your key fob, and gently jiggle it until the metal key pops out. This key can be put into the door's driver handle to unlock your car.

To replace the battery on the key fob, you must remove the cover that covers the rear. Make use of a plastic pry tool to loosen the latch that holds the black negative cable. Remove the old battery and then orient the replacement battery so that its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid damaging or breaking the contacts on the metal.

After installing the new battery, turn the key fob off and on in the ignition until the door locks up. You can then test the Kia's Key fob to ensure it's working properly.

How to replace a smart keys

You may have either a standard keyfob or a Smart Key based on the model of Kia Sportage. The smart key features an embedded mechanical key blade, unlike the standard key fob, which does not. Both kinds of key fobs contain a battery inside them that will eventually have to be replaced. It is a simple process that takes just two minutes.

Before you begin it is important to ensure that you're on a flat surface with adequate lighting and that your Kia is off. Also, remember that there are tiny components inside the fob that could fall out if not careful.


The release button for the small size is located on the lower backside. It's either a circular button or rectangular slot. When you press it button, the mechanical blade will appear and you will be able to open the key fob.

Once you have the key fob open then you can remove the old battery, and replace it. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. When you're done, the key fob will allow you to lock or unlock and start your vehicle even if it's not running.

How do you replace a mechanical key

The Kia key fob is a fantastic option that lets us lock and unlock our vehicle with the touch of one button. However, like all devices there are issues with it occasionally. There are ways to troubleshoot these issues and keep our key fobs in good working condition in the long run.

A low or dead battery is one of the most common issues. The fob could be able to cease working or work intermittently. If this is the case, try replacing the battery with a new one.

If this does not solve the issue, you can use a flathead screwdriver standard to push the fob's plastic casing open. Be careful not to damage any internal components or scratch the plastic. After opening, carefully remove the battery you have been using and replace it with a new one.

Close and open the door with the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test the fob to make sure it's working as intended. If the fob isn't working, contact a dealer or locksmith to resolve the problem. Make sure they make you an emergency key that functions in all the trunk and door cylinders in order to avoid lockouts again.

My Website: https://www.thekeylab.co.uk/kia-car-keys/