Notes

Is Tech Making Double Glazing Door Lock Repairs Better Or Worse?
Double Glazing Door Lock Repairs


Are your uPVC door or window mechanism faulty? Perhaps the door or window handles aren't able to connect correctly or are difficult to use.

It is essential that your double glazed doors function smoothly, or else you will lose energy and increase the chance of burglary. Owen the Locksmith can repair your door lock for a reasonable price.

Snapped Key

It can be a hassle when a key snaps inside the lock. It could also be a security problem because it could leave you vulnerable to an intruder if the door does not lock. Fortunately, there are quick fixes you can try to resolve the issue and get your door working properly once more.

Keep calm. If you panic and start doing a lot of fumbling around, you might just end up pushing the broken piece of the key deeper into the lock, which could make the situation much worse.

Then spray WD-40 or another penetrating oil into the lock to aid in making the broken piece slip out more easily. You can also use a screwdriver to help break up any stuck pieces that could be hindering the flow. If you're lucky enough to have a bit of the key left sticking out it, you can use a paperclip or some other thin metal object to grab it and then pull it out. Both methods are effective, but you need to be careful not to push the damaged key piece further into the keyway.

Some paperclips have grooved edges, which can serve as a hook extractor and some Jigsaw blades can also be used for this function. If you don't have one of these tools then you can bend a hook with needle-nosed pliers. Also, a pair tweezers is a good way to grasp and pull out the last piece of the key that was broken.

If you cannot remove the broken piece of key then you can use a lock deicer. This is usually available at most hardware stores. It is used to freeze any water or ice that could be in the lock.

If none of these methods appear to be working you, it's the time to contact locksmith. Fitlocks experts can quickly fix issues such as broken handles or broken keys with uPVC locks and door mechanisms. They can also reconfigure your double glazing door mechanisms to allow them to operate more easily. Book a double glazing repair via our website, or give us a phone call to discuss your needs.

Broken Cylinder

A damaged cylinder can pose a serious security threat. A locksmith professional can fix the cylinder. A locksmith will have to tap the cylinder in order to fix it. This can be done with a hammer, or any other tool. However, the best method is to use a wire or a long match. Position the match or the wire end near the keyway. The locksmith can strike the lock and break it open. This is far better than using a hammer that can cause damage to the lock.

The most frequent cause of cylinder head cracks is overheating. This can occur when the block and the cylinder head are made of different metals, such as cast-iron or aluminium. Different metals will heat up and cool off at different rates. This can cause localized hotspots to expand quicker than the rest.

Corrosion is a different reason for fractures in cylinders. If the head and block of the cylinder are not maintained in a timely manner they may be corroded or rust and cause them to expand more than expected. This can cause cracks over time.

If your uPVC window lock or door is brittle or requires a lot of pressure to turn, it could be due to several things. A faulty locking mechanism, misalignment, or the wear of the handle are typical causes of this problem.

Fortunately, this is an easy and affordable fix for the majority of homeowners with double glazing. A professional locksmith can usually solve the issue within one hour of arriving at the home. Depending on the needs of your home they will be able to replace the locking mechanism, replace the window handles, and change the gearboxes. A skilled locksmith will always be able to inform you of the most cost-effective solution for your home. double glazing repairs can even suggest upgrades to high-security 3 Star TS007 euro cylinders that will add an extra layer of protection against burglars. It is a small cost to enjoy the peace of mind that comes from knowing that your uPVC door is secure.

Broken Handle

It's not surprising that window handle locks could break. They have complex mechanisms that wear out over time. If yours breaks it may be difficult to pinpoint the cause of the issue. Make sure you fix it correctly.

Whether the problem is with the internal locking mechanism or the latch, fixing the broken handle can improve your uPVC double glazing door's security as well as help you stop the draughts. If you do not repair or replace your handle can be very expensive and can harm the door's frame as well as lock and frame, so it's worth spending some time to make sure you do it right.

With the window in the open position then loosen the screw that holds the handle using the screwdriver. The screw should be on the inside face of the back plate, and is normally covered by a screw cover for aesthetic reasons. Be careful not to lose any of the internal components within the handle, like the plates or levers on either side of the spindle. Ideally, keep them in the same order so you can replace them when needed.

Next, turn the handle so it's at 90 degrees towards the window frame. Then, loosen the screw at the back of the handle which holds it to the internal spindle by using a second screwdriver. Once this is removed, you should be capable of pulling the handle off and pull out the broken spindle. Replace it with a new one, making sure it is the same length as the previous one (you will typically find them on the internet or at hardware stores) and securely screw it into place. Do not tighten the screw too much as this could damage the handle and the window frame.

Close the handle and test it. It should function smoothly and you'll be able to open your window once more.

While you're working on the handle, make sure to ensure that your uPVC windows are shut properly. If they're not closing properly, you could experience damp or draughts in your home. Also, you could be compromising the energy efficiency of your home. A local window company, like Core Sash Windows, will be capable of adjusting the hinges on your window frames to ensure they shut correctly.

Broken Spindle

It is often the case that the spindle in the handle breaks, rather than the handle itself. This is most common in uPVC tilt and turn windows. These windows require a handle that is a lock mechanism that is located in the frame of the window. The handle is attached to a rod in the centre that in turn activates cams that resemble mushrooms, which lock into window frame keeps. If the dead latch mechanism is not able to open after the handle has been turned, it's likely the spindle is damaged. This can be a frustrating problem.

Fortunately there are options to fix this problem. A reputable locksmith can swiftly and effectively fix the issue. A professional locksmith will be able to disassemble the handle of the window by using a tool that removes the wheel portion that houses the spindle. This can be done without damaging the handle or causing other damage to the frame of the window.

Once the wheel has been removed, the technician can examine the spindle to determine what has caused it to break. This involves breaking the spindle into its constituent components and carefully observing their general condition as in addition to any specific areas of damage or excessive wear. This procedure is typically carried out by technicians working in an environment that is clean.

Next, clean the damaged spindle. This will help remove any debris or dirt that could be hindering it from operating normally. After that, the spindle could be repaired or replaced. If the technician is replacing the spindle, the dowel can be used that is the same size to the original. The technician will then drill matching holes into both pieces. This will ensure that the spindle fits perfectly with the handle.

If the damaged spindle is beyond repair, it could be necessary to replace it entirely. Home centers can sell generic replacements, but if your window design is unique, you will require contacting a cabinet maker or woodworker who can replicate the exact piece. Once the new spindle is in place it can be fitted to the handle by lining up the holes for screws in the handle with the frames existing screws. Once the new handle is firmly in place, you'll be able to operate your uPVC window.

Here's my website: https://www.repairmywindowsanddoors.co.uk/sittingbourne-windowrepair/