Notes

Getting Tired Of Patio Door Lock Repair? 10 Inspirational Resources To Revive Your Love For Patio Door Lock Repair
Patio Door Lock Repairs

Over time, the wear and tear can lead to lock malfunctions. There are a few basic steps you can take to restore the security of your uPVC door.

If it's resetting the lock or cleaning the mechanism that locks These simple fixes can make your home more secure.

Clean the Lock

While patio doors are a great option to bring the outside in and keep the elements out however, they can also pose a security risk in the event that your lock isn't operating as it should. With time, wear and tear, cold and hot weather dirt, and other debris can cause your patio door lock to become difficult to operate. With a little attention you can ensure that your lock for your patio door is always working properly.

It is essential to first clean the patio door lock as well as all moving parts. patio doors repairs will help remove any dirt and coatings that may be preventing the lock from functioning in the way it should. Begin by wiping down all the moving parts of the lock for your patio door with a damp, clean cloth. then make use of a scouring pad, or a rough damp cloth to scrub the hard-to-reach areas of the door or frame that are ingrained with dirt. Then, wipe the entire lock using a dry cloth to remove any remaining dampness and let it to dry completely before using it again.

If your patio door uses pin-tumbler locks you can apply powdered graphite to the key. You can also use a Teflon lubricant like WD-40 Multi Use Product. This type of lubricant is easy to apply and it doesn't dissolve over time. If you're not able to find a suitable lubricant, you could try using a pencil that has a thick tip. Put the pencil into the lock and move it around a bit to distribute the graphite.

Regular maintenance is also essential to keep the tracks of sliding patio doors clear from dust, dirt and other debris. These tracks are especially susceptible to snow, ice and other debris that could cause them to jam or bind. This can make it difficult for your patio door to open and shut.

Clean the track rails and rollers of sliding patio doors by removing any damaged or dirty weather stripping. Clean it and replace it. The same applies to patio door rollers which can be cleaned and sprayed with a non-stick lubricant to help them move freely.

Lubricate the moving parts

uPVC French Doors, similar to sliding patios, operate using 3 to 4, or sometimes 5 points locking mechanisms. This includes the lock cylinder and handle which is operated by keys. They also require maintenance, including lubrication of the moving parts. This can be done with an oil that is thin (never WD40) and should be done once per year.

If hinges that are sagging don't cause the problem it could be because the door is misaligned. It could be rubbing or catching against the strike plate's hole in the frame. The solution is to remove the strike plate and use a sharp chisel to enlarge the mortise that it rests in. This will allow the latch to fit into the hole, and stop it from rubbing against the frame.

When the cylinder is out of the way and out of the way, measure its width using a book or piece of wood that can fit into the gap of adjustment screw above the lock. The outer dimension is measured from the outside of door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Check the width of the lock.

If your patio door latch is difficult to turn, even after cleaning and lubricating, it's possible that it's not in alignment with the strike plate hole. Verify that the door is in a balanced position, and that the hinge screws are tight. In a lot of cases, moving the strike plate upwards or downwards will solve the issue.

The latch might not work properly in the event that the strike of the lock is too small. In this case, enlarge the opening using the hammer and chisel. Then test the latch to ensure it doesn't touch the door jamb frame or catch the frame.


You should identify the type mortise lock you have before purchasing the replacement. This can be done by looking at the faceplate on the lock and noting if it is square or round. Then, take a look at the screw holes on the current lock and note the size of each one. This information will allow you to find a replacement lock that is the exact same width and fits into your existing hole.

You'll want to identify the mortise lock and examine it for bends, scratches or other damage that need to be fixed. A badly bent or damaged latch is more likely than one that's been used a lot to break. Replace the lock if you notice indications of damage.

Once you've checked the lock and determined which kind of replacement you require then it's time to begin working on the actual repair. The old spindle and handle must be removed from the doorway to the patio. Install the new handle. Begin by installing the interior handle. Align it with the spindle, and then secure it into by using two screws or bolts. Once the interior handle is installed, you can install the exterior handle and screw it into place, too. After you've completed these steps you can test the new handles to ensure they are able to open and close with ease and that the latch is catching correctly when you strike the plate.

Check the door's Strike

The door latch and strike plate are the two parts of the lock that work together to ensure that the latch locks the door. If they are not aligned properly, the latch won't latch the door properly. This problem is usually very simple to solve.

First, check the holes in the strike plate's receiving to ensure they are free of obstructions, such as dirt or plastic plugs. Remove the screws that hold the strike plate in position. This allows it to move vertically but not separate it from the frame. Then adjust the strike plate to ensure that its holes for receiving are aligned with the latch hooks on the door latch. Once the strike plate has been adjusted then tighten all screws, and test to see whether the door closes smoothly.

These plates are difficult to reach for homeowners who have sliding patio doors. However they are vital for locking and unlocking your door. These metal plates are usually located at the top and bottom of the door jamb, which is where they are used to support the door's latch. Then, the door latch is able to slide into the strike plate to form a seal when closed. If the strike plate is damaged, rusted, or not installed correctly, it can hinder the latch from locking the door securely.

A misalignment of the strike plate and latch is a common reason for the patio lock not to close or stay. The easiest way to check for this is to perform the "lipstick test." Rub some lipstick along the edge of the deadbolt, then attach masking tape over it. The lipstick will leave the mark when you close the door. This will indicate exactly where the latch joins the strike plate. If the mark is too low or high, you can easily alter the strike plate.

The sliding patio door locks keep your home safe from intruders, and if they're not working properly, you need to fix the problem quickly. If you follow these steps, you can repair the lock on your patio door and restore its functionality in no time.

My Website: https://www.repairmywindowsanddoors.co.uk/patio-door-repairs-peterborough/