Notes

12 Companies Leading The Way In Fiat 500 Keys
Fiat Panda Key Fob Replacement

Fiat Panda key fobs contain a transponder chip which sends the signal to your vehicle to open the doors or start the engine. The fob might stop working for a variety.

The most commonly cited reason for key fob failure is a dead coin battery. Other causes include water damages as well as a defective module and interference signals.

Dead Coin Battery

If the battery in your key fob has failed, the initial thing to do is replace it. Use a button cell that has the same voltage, size, and specifications as the old one.

If the key fob was exposed to water, like a splash of rain or salt water at the beach, it will need to be cleaned before it is able to be used again. fiat replacement key is to use a paper towel that has been soaked in isopropyl, or electronic cleaner.

If the key fob hasn't been exposed to water, but it is still not working it could be due to a problem with the receiver module or an internal electronic chip. Reprogramming the keyfob using an OBDII scan can assist in these situations.

Water Damage

There could be water damage if your key fob was submerged in a puddle, pool or washing machine. It's usually possible to get it working by taking out the batteries and cleaning the circuit board with rubbing alcohol. It's best to allow the device to completely dry before installing the battery.

If your key fob stopped working even after replacing the battery and changing the program, you could have a faulty receiver module. You can find reprogramming instructions for most remote key fobs on YouTube or in the owner's guide. You can also reset your computer in your car with the OBDII scanner tool.

Faulty Receiver Module

The key fob is equipped with the chip that communicates with the vehicle's system. If this chip becomes damaged, it will be unable to longer be able to send or receive signals to the vehicle. This could be due to dropping the key fob or by water exposure. If the key fob stopped working after exposure to water, it is possible to fix the issue by cleaning the chip using isopropyl alcohol or electronic cleaner.

If the key fob won't respond to cleaning, it is possible that the module has a fault and needs to be replaced. A damaged receiver can cause the key to cease to function. This is usually caused by electromagnetic interference.

Faulty Electronic Chip

The electronic chip in the key fob is a crucial component of the anti-theft systems in your car. It transmits a message to the immobiliser inside your car to tell it whether the key is legitimate. Your car won't start in the event that the chip is damaged.

A faulty chip can also be caused by interference signals from objects, bad weather conditions or transmitters operating on the same frequency as your car. In this case, you will need an entirely new key fob.

Contacts to the battery are not working properly.

The battery contacts on the key fob could be damaged by excessive usage. If they are bent, or damaged, the fob will not transmit any signals to receiver modules inside the vehicle.

Modern fobs feature rubber seals that block out water. A splash of water or light rain is fine, but submerging them in salt water could harm the electronic chip.

The key fob has a chip that communicates with the vehicle's immobilizer system to begin it. This system utilizes cryptocoding systems in modern vehicles and the older red key system in older ones. This chip will need to be changed if it is damaged.

The 12 Volt Battery is faulty

A faulty battery can cause the remote to cease working. The car's system will not recognize the remote if this happens.

Test the battery with the help of a voltmeter to determine its capacity. A fully charged battery should display 12.6 volts. If the reading drops dramatically then it's time to replace it.


To test a battery's capacity put an electrical load on it for a couple of minutes. This will eliminate approximately 1% of the surface charge. Then measure the voltage again. The higher the capacity of the battery is, the longer it will keep its voltage. It is ideal to maintain close to 12 volts over several minutes.

Faulty Radio Signal

This is the most frequent reason for a key fob that ceases to send signals to the car. The battery can be replaced to solve this problem. It is essential to purchase an identical battery dimensions and voltage as the original.

Fobs endure a lot of punishment, and aren't indestructible. The battery buttons and the contacts are fragile and can be bent or damaged from rough use.

Other objects or transmitters using the same frequency could also disrupt the signal. A light control panel in your home, for example can interfere with key fobs which use the same frequency. This can interfere with the remote control of your car.

Incorrect OBDII Scan Tool

There are many reasons why a scanner may not work. Some are more complicated than others.

Professional scan tools allow mechanics to observe the car's networks and conduct a variety self-tests. These tools can save time, but they're expensive and not accessible to the majority of DIYers.

If your OBD2 scanner doesn't work make sure you check the voltage at terminal 16 (scan tool power) and terminal 4 (chassis ground). If these are OK it's possible that a fuse has failed. This is one of the most frequent causes of failures in the scan tool. The easiest fix is to replace the fuse which has blown.

Homepage: https://www.thekeylab.co.uk/fiat-car-keys/