Notes

The Ugly The Truth About Fiat Panda Key Fob Replacement
replacement fiat key for the Fiat 500 allows you to easily open doors and start your car. There are many reasons the key fob might stop working. This could be due to a dead battery or water damage, problems with receiver modules, as well as interference.

This listing is for a NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that must be programmed professionally by a local locksmith (click here for Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob will not function is due to a dead battery. Modern key fobs operate with a limited operating range and must be within only a few feet from the car to operate. If you're not close to your vehicle, and you press the key fob button, the car won't respond and will display the "Key Fob Not Detected" message in the instrument cluster.

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a fresh one of a reliable brand, such as Panasonic Duracell or Energizer. You can usually find them in your local hardware store, or online.

After you've replaced the coin cell battery It is possible to test it by standing next to your Fiat 500 and pressing the buttons. The parking lights should light up and the key fob will operate the lock and unlock switches.

If the fob's remote doesn't work after replacing the battery, it might have water damage that stops it from connecting to the receiver module inside your car. Water damage can happen in a variety of ways, from small splashes to submerging the fob in salt water at the beach. If you suspect that your fob has been exposed to water, place it in a rice bag to draw out the moisture. If this doesn't work, the fob might need to be reprogrammed by an experienced auto locksmith or by the dealer.

Water Damage

Water damage can occur when you immerse the fob in the ocean, or wash it in a washing machine. Saltwater is especially dangerous to the fob's circuit board that can cause it to short out and eventually end up dying. It's not good to submerge the fob in water, but don't give it up even if you accidentally drop the fob in the water or don't take it out of your pocket.

Remove the battery first. Before replacing the battery, clean the electronic chip using isopropyl or another similar product. Next try the fob and test if it works. If the key does not work, it might need to be reset. This is usually done by a professional or dealer auto locksmith.

If the key is newer and has never been programmed to your car it is likely to need to be replaced completely. A professional locksmith in the automotive industry will be able to complete this process. The locksmith will need the key cut to match your vehicle's ignition. The locksmith also needs to reprogram your fob into the car's system. This is a cheap and quick process that could be completed on the same day.

Receiver Module Issues

Your 500 key fob may not work because it's out of range. The remote's range is of 30 feet. So in the event that you are far away from your vehicle it will not respond to your commands. You can easily remedy this by moving your remote closer to your vehicle until it responds.

If you've replaced the battery on your coin (commonly known as"button" or "button" or "watch") and your fob doesn't function, it could have an internal circuit board issue. Reprogramming the fob typically resolves the issue. The instructions are available for most vehicles on YouTube or in the owner's manual.


It is sometimes necessary to replace the metal clips that hold the coin batteries in the correct position. If they become loose, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare cases it is possible that the fob will become disconnected from your vehicle due to software issues or hardware issues. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain situations, they may need to reinstall the software on your body control module as well.

Interference

Interference can also cause the key fob to not receive or transmit signals. This can occur when the keyfob's location is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons the key fob could not function include a poor connection to the buttons or the internal chip, or water damage.

If the key fob stopped working one day in the middle of the night, or after trying everything you can do at home to resolve it e.g. replacing batteries, reprogramming or using the spare key fob, you could have a defective receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy method to reset all on-board systems in your 500, including the key fob. Disconnect the 12 volt battery for about 15 minutes by taking off the negative cable first then the positive cable. Then, reconnect the battery. This will eliminate any remaining electricity, and restart the computer of your car. This could help you get your key fob working again. If the issue persists, you should speak with an expert technician. They will be able diagnose the root of any problems.

Here's my website: https://www.thekeylab.co.uk/fiat-car-keys/