Notes

5 Replacing Upvc Window Handles Lessons From Professionals
Replacing uPVC Window Handles

Switching the handles of windows made of upvc is a simple job. It is crucial to make sure that the new handle fits inside the spindle cutout of the window mechanism.

If the steps listed below are followed properly, any cockspur handle should fit most windows. The height of the step of the handle is crucial.

What to Find

Over time, uPVC handles on many windows in the UK may begin to show signs of wear and wear and tear. If this happens, the window handle may become loose or difficult to operate, which makes it essential to replace it. Anyone who is proficient working with basic hand tools can complete this relatively simple task.

The first thing to do is ensure that the handle is securely attached to the window frame and in the open position. The next step is to locate the fixing screws or pins that hold the handle in the position it is in. They are usually on the inside of the handle. They can be removed with the screwdriver and pliers.

When the handle has become loose, gently pull it away from its hinges. Then, you'll have to locate a new handle in the same size and style. This can be accomplished in a DIY store or online. The procedure should take just five minutes and requires a screwdriver is all you need.

One crucial aspect to take into consideration when replacing a uPVC window handle is its step height. This is the distance between the handle's base and where it is placed in the window frame. This is a typical measurement, and you should verify the height of the step before purchasing an replacement handle.

Depending on the type of handle you have, there are different sizes to choose from. Inline handles can be found for uPVC windows that have lug centres of 31mm, while cockspur handles have centers of lugs of 43mm. Tilt and turn handles are commonly found on windows made of uPVC and they have a special design that allows windows to be tilted in to allow for ventilation, and then turned to fully open the window.

The most frequent uPVC handle cracks are internal, instead of a break at the base. This can make them hard to open and therefore it is essential to ensure that any replacement handle you buy has the same spindle length that your current one.


Remove the old handle

A poorly fitted or damaged window handles may cause double-glazed windows to close or open in a way that isn't correct and may result in them getting stuck. This could be due to a number of reasons, including general wear and tear on the metal handle or corrosion. In these instances, it is important to seek replacement handles made of upvc as soon as possible in order to prevent further damage and loss of function.

One of the first steps that you should do when replacing upvc window handles is to remove the old handle from the window. Start by removing the screw when the handle in closed position. This will reveal a screw and once removed, you can then begin to take off the handle itself. It is recommended to use an electric screwdriver for this, as it makes the job easier and faster.

It is also important to note that the screws on the handle could be hidden behind plastic caps, therefore it is recommended to take the Stanley knife to the screw covers and take them off. After removing the handle, you'll have to examine the square cutout on the base to make sure that the new handle for the window lock is compatible. This is crucial as you will need to measure the length of the spindle of the old handle to make sure it is the same size as the window mechanism and the handle spindle cut out.

There are door handles Repair My Windows And Doors of Upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles that have two screws and Spade handles, which have flat arms and can be used either side of the upvc window. Once you have a suitable replacement, it's simply a case of screwing the handle into place and ensuring that the spindle is fitted into the lock mechanism. After that, you can then tighten the handle to the window frame. The replacement upvc handle should now be secure.

Measure the Spindle

If you're looking to replace a Upvc handle that has collapsed, it's likely the spindle holding it in place is damaged or is loose. In some instances, this could be fixed with a screw or pin to tighten it. In certain situations it is necessary to replace the handle. There are many kinds of window handles made of upvc. There are three types of handles: inline espagnolette tilt-and-turn, and cockspur. Each kind has a distinct method for installing and replacing the handle.

It is crucial to measure the current handle prior to purchasing an alternative. This will ensure that the handle will fit the window correctly and will be of the correct size. Luckily, all handles conform to industry standards for sizing, so it's fairly easy to find the right size.

To measure the size of your handle first, take it out of the window by turning it back to the open position. You should be able to determine the dimensions of the pin or screw that holds the handle. Use a ruler or a tape measure to determine how long the spindle is. Once you know the length of your spindle, it is possible to buy a replacement of the exact same length.

The step height of a upvc window handle is also a factor to consider when buying replacements. The step height is measured from the base to the point where the handle is positioned on the frame. Typically, this will be around 21mm for uPVC windows or 9mm for aluminium. To ensure that the new handle will work, you can drop something into the space to check the distance it will go before it comes into contact with an obstruction.

Cockspur handles often have different backset heights, based on the style of window they are installed in. Inline espag handles have the standard height of 43mm centre to centre (2 fixing points). Cockspur handles however they have different backsets dependent on the style of the window they are in. This is because they have a spur that extends from the handle and is locked onto a cockspur wedge striking plate.

Install the new handle

After you've chosen the new handle, ensure that it is aligned with the screw holes on the door. Secure it using the screws provided. If you're replacing the latch lever it can be put in similarly to the main door handle. Then, you can reattach the door trim to conceal the mounting screws and finish off your project.

Tips: To take the head of the metal from the wooden wedge make sure the handle is held so that its broad end rests on the floor. Use a hammer to tap the thin end of the handle. Be careful not to scratch the handle or the handle spindle.

Here's my website: https://www.repairmywindowsanddoors.co.uk/swanley-windowrepair/