Notes

The Ultimate Guide To Double Glazing Door Lock Repairs
Double Glazing Door Lock Repairs

Are your uPVC window or door mechanism faulty? Maybe the window or door handles aren't aligned properly or are difficult to use.


It's important that your double glazed doors work smoothly, otherwise you'll be wasting energy and increase the chances of burglary. Owen the Locksmith will be able to repair your door lock for a reasonable cost.

Snapped Key

It can be quite frustrating when a key gets stuck into a lock. This can also be a security risk, as it may leave you vulnerable to an intruder if the door does not lock. There are a few easy fixes you can make to resolve the issue and get your door working again.

Be calm. If you panic and begin poking around wildly you may end up pushing the damaged piece of the key further into the lock, making the situation much worse.

Then, spray WD-40 or another penetrating oil into the lock to make the broken piece slip out more easily. You can also make use of a screwdriver to break up any pieces stuck that might be hindering the flow. If you have a piece of the key that's stuck out, grab it with a paperclip or other thin metal object and pull it. Both methods work, but be very careful not to push the broken piece of the key deeper into the keyway.

Some paperclips have grooved edges which can be used as hook extractors. Jigsaw blades can also work well for this. If you don't have any of these items then you can bend a hook using needle-nosed pliers. Additionally, you can use a pair of tweezers grab and remove the last bit of the broken keys.

If you cannot remove the broken key piece then you can use a lock deicer. It's usually available at all hardware stores. It works by freezing any moisture or ice that might be inside the lock.

If none of these solutions seem to work, it might be time to consult a locksmith. Fitlocks experts can fix problems such as broken handles and broken keys with uPVC locks and door mechanisms. They can also reconfigure double glazing door mechanisms to ensure that they are more easy to operate. Get a double glazing repair via our website, or give us a phone call to discuss your requirements.

Broken Cylinder

A broken cylinder can be an extremely risky security issue. A locksmith professional can repair the cylinder. To fix the cylinder a locksmith will need to tap it. This can be done using the hammer or other tool. However, the most effective method is to use a wire or a long match. Then, position the end of the match or wire near the keyway. After that, the locksmith will strike the lock and break it open. This is superior to using a hammer that could cause damage to the lock.

The most common cause of cracks in the head of a cylinder is due to overheating. This can happen when the cylinder block as well as the cylinder head are made of different metals, such as cast iron and aluminium. When different metals heat up and cool down at different rates, it could create hotspots in the local area that expand faster than the rest of the cylinder head, thus leading to cracks.

Corrosion can be a reason for cylinder fractures. If the cylinder head and the cylinder block aren't properly maintained, it can result in corrosion or rust and cause them to expand at a greater rates than they should. Over time, this can also cause cracks.

If your uPVC window lock or door is brittle or requires lots of pressure to turn, it can be the result of a number of things. This issue could result from a defective locking mechanism or misalignment, and also a worn out handle.

It is a quick and inexpensive fix that most double glazing owners can accomplish. double glazing repair near me is able to solve this issue within an hour of arriving at your home. Depending on the needs of your home they will be able to replace the locking mechanism, change the window handles, and also change the gearboxes. A professional locksmith will be able to advise you of the most cost-effective solution for your home. They can even recommend upgrades to 3 Star security TS007 euro cylinders that will provide an extra layer of security against burglars. It is a small cost to pay for the peace-of-mind that comes from knowing your uPVC door is secure.

Broken Handle

Window handle locks have complex mechanisms that deteriorate with time and use, so it's not a surprise that they sometimes break. If yours breaks it's difficult to determine the source of the problem and make sure you fix it correctly.

Fixing your broken handle, whether it's the internal latch or the locking mechanism can increase the security of your uPVC door and reduce the risk of draughts. Incorrectly repairing or replacing your handle can be expensive and could cause damage to the door's frame and lock and frame, so it's worth spending some time to make sure you do it right.

With the window in the open position then loosen the screw that secures the handle using the screwdriver. It should be located on the inside face of the back plate, and is normally concealed by an aesthetically pleasing cover for the screw reasons. Be sure to not damage any of the internal components inside the handle, for example the plates or levers on either side of the spindle. It is best to keep them in the same order so you can re-install them in the event of a need.

Then, using a second screwdriver take the screw off that connects the handle to the spindle at the back. Once the screw is loose, you should be able to pull the handle off and take out the broken spindle. Replace it with a new spindle, ensuring it's the same length (you can buy them on the internet or in hardware stores). Screw it in the frame. Do not tighten the screw too much as this can damage the handle and the window frame.

Close the handle and test it. Hopefully, it will work smoothly and you'll be able to unlock your window.

Be sure to double-check that your uPVC window is closing properly while you're working with the handle. If they're not, you could experience damp and draughts inside your home, as well as compromising your home's energy efficiency. Core Sash Windows is a local window company that can alter the hinges of the window frames to ensure that they shut correctly.

Broken Spindle

It is usually the case that the spindle inside a handle breaks rather than the handle itself. This is particularly common with uPVC tilt-and-turn windows. These windows require a handle that operates an locking device within the frame of the window. The handle is attached to a rod in the centre that in turn activates mushroom-like locking cams, these lock into window frame keeps. If the dead latch mechanism fails to open when the handle is turned, it is possible that the spindle is broken This can be an extremely frustrating issue.

There are solutions to this issue. A reputable locksmith can swiftly and effectively fix the issue. A reputable locksmith will be able disassemble the window's handle using a tool to take out the wheel from the area that houses the spindle. This can be done with no damage to the handle or the window frame.

After removing the wheel, the technician will inspect the spindle and identify what caused it to break. This involves disassembling the spindle and inspecting each component part, noting any wear or damage. This process is usually performed by technicians in an environment that is clean.

Next, clean the damaged spindle. This will help get rid of any dirt or other debris that may be obstructing it from working normally. After this the spindle can be repaired or replaced. If the technician is replacing the spindle he can use a dowel that is comparable in size to the original. The technician will then drill matching holes into both pieces. This ensures that the new spindle is precisely matched to the handle.

If the damaged spindle cannot be repaired it may require replacement completely. Home centers offer generic replacements. However, If the style of your window is rare then you will need to find a woodworker or cabinet maker who can make the exact model for you. Once the new spindle is installed, it can be fitted to the handle by line up the holes for screws in the handle with the frames existing screws. Once the handle is seated, you can operate your uPVC windows.

Read More: https://www.repairmywindowsanddoors.co.uk/suttoncoldfield-windowrepair/