Notes

The 3 Greatest Moments In Ghost Immobiliser Fitting History
Ghost Immobiliser Fitting

Protect your vehicle against key theft, cloning, and hacking by using the first aftermarket CAN-Immobiliser. With the additional option to link to a Ghost app and GPS tracking system that can send you call alerts in the event that your vehicle is damaged with or stolen.

Installing an Ghost immobiliser is fairly simple for the qualified technician. It is important to have the proper tools and heat shrink tubing.

Getting Started

Contrary to physical theft protection devices like wheel locks and car alarms, ghost immobilisers safeguard your vehicle without the need of LED indications or key fobs. Instead, they connect directly to the ECU's CAN network and can only be activated after entering a PIN code sequence. This gives a greater level of protection against key hacking, ECU swapping and cloning.

Installing a ghost immobiliser Birmingham requires a high level of agility and accuracy. It can be a bit like walking through a minefield; one misstep could cause irreparable damage to the circuits of your vehicle's electrical system. It is essential to comprehend the procedure for installing and prepare your vehicle in a timely manner.

You will need to remove interior panels from the vehicle to make room for your immobiliser. Once you've found the ideal location to hide it, secure it in place with cable ties to keep it from being taken away or damaged. Then, tidy up the wiring by tying loose wires and using insulation tape or heat shrink tubing to cover exposed connections. This will reduce the risk of a short circuit that is not intended to happen while also improving the appearance and reducing the risk of theft.

Then, locate a source of continuous 12V power and a grounding point for the ghost immobiliser. Once you've found these, test the power wires using a multimeter to ensure they're delivering the same voltage. Connect the CAN H & the CAN L wires of your immobiliser with the power source and grounding points.

After you've made all the connections required, it's important to double-check the connections and check the immobiliser for signs of corrosion or other damage. Also, test the system to ensure it's functioning properly by entering a PIN code and then starting the engine. This should be a regular part of your routine, because it will allow you to identify any issues that may be occurring early on. Regular testing also helps to extend the life of the device, and ensure it's functioning at its best.

Preparing the Vehicle

The installation of a Ghost immobiliser is a complex task that requires the right tools and understanding. A wiring diagram of the vehicle is vital for locating the correct wires and making precise connections. A multimeter is a great tool to check the electrical value and ensure security. Insulation tape and cable tie can be used to secure connections and prevent being tampered with. A user manual is available for the Ghost Immobiliser. It will provide you with specific instructions tailored to that model.

Once installed, the ghost immobiliser will stop unauthorised engine start-ups by requiring that the owner enter a unique code using the buttons on the steering wheel or console. This can be done manually or remotely via an app for mobile phones, and the code is able to be modified by the vehicle's owner at any time. The device is also silent and is undetectable to thieves because it does not emit radio frequencies.

A ghost immobiliser is connected directly to the vehicle's CAN bus, which is a network that communicates with all of the vehicle's electronic control units (ECUs). It intercepts signals from the ECUs and stops the engine from starting when the ECU detects a false signal. The system is weatherproof and tamperproof. It has no keys or LED indicators to attract thieves' attention.

It can be mounted behind the dashboard or in a discreet area, so it isn't seen by thieves and does not interfere with the vehicle's performance. It can be mounted in a small jar, so that it is less likely to be spotted by unscrupulous salespeople during a test-drive.

Its stealthy operation, along with its integration into the vehicle's CAN-bus system, can be an effective deterrent to modern vehicle theft techniques like signal relay attacks and key copying. The system can be paired with other security measures to create a powerful barrier that can deter even the most persistent thieves. More and more insurance companies suggest or require ghost immobilisers as they can cut down on monthly premiums.

Making autowatch ghost immobiliser cost

Unlike traditional security systems that can be heard by thieves, ghost immobilisers are silent and prevent them from knowing when your vehicle has been switched on. They also block high-tech methods employed to steal vehicles, like OBD port hacking. They can also be installed without causing permanent marks in your vehicle, making them an excellent option for those who are planning to sell their car in the near future.

The Autowatch Ghost 2 CANbus immobiliser is among the most recent and most reliable methods for preventing car theft. It blocks your engine through the CAN data network and generates a unique PIN code which is difficult to steal from criminals. It can be used in various automobiles, and it can work with many features already installed like car alarms, steering wheel locks, GPS trackers and door lock bypass.

If you choose to use a Ghost immobiliser for your vehicle, be sure to refer to the wiring diagram to determine the wires to connect. Check their locations to make sure they are correct, and then label them or tape them to help you remember them. You will also have to locate a reliable power source (12V) for the system, as well as an earthing. Once you have all the components, you can start making the connections to complete the installation.

When the ghost immobiliser is connected to your CAN bus, it will prevent your vehicle from starting until you enter a pin number using the buttons on the steering wheel or dashboard. This will stop ECU hacking, key cloning, and other techniques of theft from vehicles. Additionally, it can be used in conjunction with other Thatcham-approved security accessories, such as alarms and tyre clamps, to give your car an additional level of protection.


As the UK automotive aftermarket industry expands as do the options to secure your vehicle. There are so many ways for thieves to get into your vehicle and steal it, therefore it's vital to take every precaution to ensure that it isn't taken away. Ghost immobilisers are an increasingly popular option for car owners who are responsible.

Testing the System

The Ghost Immobiliser uses a CAN data network to communicate with the vehicle's ECU which stops the engine from starting until a specific PIN code is entered. This makes it very difficult for thieves to copy your key fob and start your car, and even more difficult to disable the system by hacking into its electronic components.

Ghost Immobilisers can also be used in conjunction with GPS tracking devices that can aid in tracking your vehicle and track it in the event of theft. This feature is not an option that is commonly used in aftermarket security solutions however it's a great option to increase your security and give you peace of mind knowing your vehicle is protected.

The Ghost-II immobiliser not only provides greater security, but also a convenient experience for the user, by eliminating the need to use additional key fobs or devices. It features an easy and intuitive PIN code entry system that is seamlessly integrated into your everyday routine. It also comes with convenience features and deactivation options that let you to temporarily disable the immobiliser so that you can park or service your vehicle.

Before you begin the installation process, familiarise yourself with your vehicle's wiring and prepare the tools. A basic set of tools will enable you to make precise connections. A multimeter can be used to verify electrical values. Insulation tape and heat-shrink tubing is essential to protect connections from short circuits. Cable ties can be used to secure wiring. It's also important to work in a place which is well-lit and wear safety equipment when working with electrical tools and components.

After you've completed the installation, you should test the Ghost immobiliser to ensure that it's functioning properly. It is recommended to first start the car without entering the PIN. If this fails, you'll have to test the system again and perform a more thorough inspection of the connections.

The Ghost Immobiliser, unlike other security systems, is a secret device that cannot be identified by thieves. It is also more effective than physical deterrents such as wheel clamps and steering locks. It is TASSA acknowledged and approved by some insurance companies, which makes it a cost-effective investment that can give you the peace of mind you deserve.

Homepage: https://severinsen-simmons-2.technetbloggers.de/why-ghost-installation-is-the-right-choice-for-you-1733936418