Notes

This Story Behind Ghost Immobiliser Install Is One That Will Haunt You Forever!
Autowatch Ghost Immobiliser Installation

The Ghost is the UK's most advanced aftermarket immobiliser for the CAN bus. It's discreet It does not include LED indicators or key fobs and is hidden within the vehicle's wiring.

It also permits the user to turn off the system temporarily by using Transport Mode in the event of renting their vehicle. This guide will take you through the installation of a Ghost immobiliser.

Professional Installation

The Autowatch Ghost immobiliser protects your car against key cloning attacks, hacking attacks and relay attacks. The system is linked directly to the ECU of your car and protected by a pin code you select. It is inaccessible to thieves using diagnostic scanners or other modern methods. It cannot be disabled using circuit cuts.

The system is simple to use, however professional installation is recommended to ensure a clean connection with the ECU of your vehicle. An approved installer from Thatcham can assist with the installation and programming of your Ghost system. They can also suggest an alarm or tracking system to complete the protection package for your vehicle.

The first step is to disconnect your battery in order to avoid the possibility of airbag deployment and short circuits. After this is completed, the installer can safely begin work. Basic hand tools are helpful for securing connections with precision, while a multimeter can be used to test electrical values and ensure safety. Cable tie and insulation tape are essential to protect connections and keep wiring neat. Lastly, the user manual offers specific instructions tailored to your Ghost Immobiliser model.


It is crucial to select the right grounding spot that is free of dirt or paint during installation. The installer should ensure that the immobiliser's CAN H and CAN L wires are connected to the correct ports on the vehicle's ECU. Based on the model, these wires might need to be soldered or plugged in. To ensure a secure and long-lasting connection it is recommended you choose a high-quality plug.

After the installation is completed Once the installation is completed, the customer can enable the Transport Mode. This allows mechanics or valet parking to use the vehicle, without having to know the pin code. To do this, the customer has to press the button for service on the dashboard 5 times in the space of two seconds. After that the system will verify with 5 indication signals.

The Autowatch Ghost 2 is a highly effective immobiliser that's TASSA verified and Thatcham approved. It's a great choice for those who rent out their vehicles frequently on platforms like Turo. An immobiliser can reduce insurance costs, since it lowers the chance of theft.

Getting Started

If you are looking for a solution that will safeguard your vehicle from theft, you can't go wrong with an autowatch ghost immobiliser. It prevents your car from starting even if someone steals or copies your key. It is possible because of its advanced technology that prevents the engine from starting until the correct PIN code has been entered.

The device connects to the vehicle's bus network, CAN, allowing direct communication with the ECU. It makes use of the buttons on your dashboard and steering wheel to create a unique sequence which only you know. This makes it impossible for anyone else to start your vehicle. This is the most secure way to safeguard your pride and joy. It will ensure that your car's value remains intact should you ever decide to sell it.

Installing a ghost ignition is an easy process, however, it is important to follow the instructions carefully to avoid problems with the electrical system and malfunctions. You'll need to locate a 12V power supply and a good grounding on the car's chassis. After that, you are able to begin connecting the wires for the immobiliser. Make use of high-quality connectors and soldering techniques to ensure a solid connection. Also, make sure to cover the connections with heat shrink tubing and insulation tape to shield them from electrical short circuits and other problems.

Once the wires have been connected, you can connect the battery and begin the engine to check if the immobiliser is working. When everything is functioning correctly, you can install it in a safe location beneath the dash or anywhere else in the vehicle. Be sure to hide it well so that thieves can't get it into a compromising position.

The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified this means it complies with the highest standards of security and is a fantastic protection against car thieves. It is a superior defense against key cloning, hacking and relay attacks. It cannot be disabled without knowing the code. The device is easy to use and can be set into the service valet setting to ensure that your vehicle won't be activated when you take it for an MOT or servicing.

Wiring

The Ghost Immobiliser is a cutting-edge security system specifically designed to deter theft of vehicles. It communicates with your vehicle's ECU and directly connects to its CAN bus. In contrast to other aftermarket systems that require the removal of circuit components The Ghost Immobiliser does not interfere with any of the factory settings of your vehicle.

It's also totally undetectable by thieves using diagnostic scanners. The system doesn't send or receive radio frequency signals but instead uses CAN data for communication with your ECU. Additionally, it doesn't require any modifications to your vehicle's existing key fobs.

To make use of the Ghost Immobiliser simply switch on the ignition of your car and enter your disarm sequence (either one or two buttons). The indicator will flash twice to confirm that you've entered the correct code. After this, you can start your car and drive away safely.

Once installed Once installed, the Ghost Immobiliser will protect your car from hacking and key cloning, while protecting the value of your pride and joy. If you have to surrender your vehicle for service or valet parking The Ghost Immobiliser will be temporarily disabled in Transport Mode.

You'll require a constant power source (12V) in addition to a grounding point to complete the installation of a Ghost immobiliser. Make sure both are properly insulated and can be touched. Cable ties are also suggested to secure the wires. This will reduce the possibility of theft by potential thieves. Be sure to verify the locations of these points to avoid making mistakes and mark them with a piece of tape or label. Verify have a peek at these guys for signs they are wearing out. Make sure that all connections are securely in place, and properly protected. Don't forget to test your Ghost Immobiliser after installation has been completed. This will confirm that the unit is operating properly and that all connections and insulation are safe. If there are any issues, be sure to address them immediately.

Testing

The Autowatch Ghost immobiliser is an innovative vehicle security system that integrates seamlessly with your vehicle's ECU to prevent the motor from starting without authorization. Its cutting-edge technology protects your vehicle from hacking and key cloning along with other common methods used by thieves to steal vehicles. The Ghost works in conjunction with existing alarm and tracking systems to provide the most effective protection for your vehicle. The Ghost's unique features and subtle design make it a popular choice for car enthusiasts and security-conscious drivers alike.

It is essential to follow the steps of installation in order to ensure correct integration of the Ghost Immobiliser. Refer to the wiring diagram of your vehicle as it will assist you in locating and connecting the wires. You'll need to determine the power and grounding sources. Once you've located them, you'll need to mark the points to make them easy to locate when installing. In addition, it is important to use top-quality tools and materials. Basic hand tools can help you make precise connections. A multimeter can verify electrical values, and also ensure security. Insulation tape and cable ties can help keep connections tidy and neat. Finally, a user manual will give specific guidelines specific to your Ghost model.

It is crucial to test the system prior to installing it. Enter the PIN code into the system, and then start the vehicle. This test will verify that the immobiliser works as intended and stop unauthorised vehicle starts. It's recommended to perform this step regularly as part of your regular vehicle inspections to ensure that the system is operating correctly.

After the installation is completed, you can start driving your car with confidence. The Ghost will help keep your precious possessions safe from would-be thieves and ensure that no one can drive off with your vehicle without the proper PIN code. The Ghost can be linked to an approved Thatcham tracker that identifies any attempts to steal or tamper with. This lets you track your vehicle if it is stolen.

The Ghost is compatible with a variety of automobiles, including those from all major manufacturers. Monty's Locksmith can assist you in securing your vehicle with this innovative device. Contact us today to learn more about our services and installation options. We are a TASSA Installer who is registered which guarantees that we follow strict guidelines and procedures when installing our products. This assures customers as well as insurance companies and law enforcement agencies that installations are carried out safely and properly.

Website: https://www.thekeylab.co.uk/car-security-ghost-immobiliser/