Notes

11 Ways To Fully Redesign Your Boarding Up A Door
How to Go About Boarding Up a Door

Protecting vacant investment properties against the elements is attainable by board up a door. It may not prevent every damage but it can assist to prevent some of the issues that are associated with severe storms.

Boarding up windows and doors can also deter burglars and vandals as well as squatters. Installing plywood panels over openings could be time-consuming and costly.

Take a measurement of the door

The first thing you'll need is tape measure. It is a good idea to keep a ladder or a chair close by in case you require to see more clearly the top of the frame. Wear gloves and protective glasses when you make use of these tools.

Start by measuring the door's width. This can be done by running an x-ray measure horizontally across the door. Be sure to take out all additional parts of the door, for instance a sweep, before measuring. Then, measure the height by measuring from the floor to the sill plate or lintel. It is essential to measure multiple locations particularly with older doors, as they are not always an exact rectangle. If the measurements differ take the largest number.

You'll have to determine the size of the frame once you've measured the height and width. It should be at a minimum 2'' wider and 1'' higher than the door. 2'' higher. This will give you plenty of space to shim the frame and door to fit.

It's a good idea to take off the trim or casing around the jambs of your door to be able to see the studs. This will help you determine the exact dimensions of the space between the studs and the frame.

After taking off the trim, take a measurement of the length of your door frame using a tape measure. The frame should be measured at three different places and then use the most compact measurement. You should also determine the height of the frame from top to bottom, on both sides. Use the shortest measurement for the width of your door.

If you're having difficulty with these measurements It's a good idea at this point to consult a professional and have them come to your home to do the measuring for you. They'll be able to give you the exact kind of door and size you need and the best way to prepare the frame to accommodate the door you want to buy.

Cut the Plywood

A door frame is typically made of a series of studs or boards that create a hollow space around the door. Two hinges are attached to the studs, and they hold the door in place. If you want to refinish a door, you will need to remove it from its hinges overnight. To prevent insects from entering your home and to secure the door opening, a quick and easy method to board the door is to put plywood inside the opening. This is a simple process without the need to screw or nail the plywood to the door frame.

Plywood is affordable, simple to work with and looks stunning when finished. This makes it the perfect material for an interim solution to problems that require the removal of the door that is in use and refinishing or installing a new one. It is also useful to secure the opening of a room that is being renovated, such as an unfinished basement or construction site.

Start by measuring the width of the door opening and the height. Draw the dimensions on the plywood using an utility knife and a drywall square or other straight edge made of metal. Then, snap the chalkline along each line to indicate where you want to cut. Then utilize circular saws to cut out the plywood to size.

It is crucial to shield your ears and eyes when cutting plywood. If possible wear eye protection and earplugs as you are working. It is also essential to use a sharp blade with many teeth, which will permit you to cut quickly and with minimal tear-out. Use a small piece of wood to guide the blade. Hold it a hair's width away from the mark when cutting.

An effective way to hold the plywood in place without screwing it to the studs is to attach two braces at each end. Place one of the braces on the inside of the door and the one on the outside. Install a deck screw in each hole, and then tighten by using an open-end ratchet.

Fix the Plywood


Once you have a sheet of plywood cut to the proper dimensions and with the holes for the door frame's rails and stiles already drilled and ready to fasten the panel to the frame. This is a straightforward project that does not require extensive carpentry skills, provided you follow the correct procedures and use the proper tools.

Set up a table near the doorway, with two sawhorses at each end, as well as framing 2x4s. Utilize the marks you made during the measurement procedure to guide you in cutting the plywood. Mark the lines using a utility knife and a drywall square or any other metal straight edge. This will create an outline for the saw blade and keep the wood from splintering when cutting the plywood.

Put on eye protection and cut along the scored lines using a circular or table saw equipped with a fine-tooth blade. Sand the edges of the panels with 120-grit paper to smooth it out and eliminate any burrs. After sanding process, apply a coat of wood sealer on the plywood panels and let dry as directed by the manufacturer.

Install the hinges on the door frame. If you're using a hinge with a T-hinge drill holes in the outer side of your door to accommodate the strap portion of the hinges. Then, you can screw the outside hinge to the frame with a screwdriver. Repeat the procedure for each hinge on the interior of your door. Be careful not to tighten them too much or the door could move.

If you're using an outside hinged door with only one T you can make it easier to close and lock using a chain latch by putting a piece wire through the loops of the hinges outside. Bend a small piece of tie wire in half and fish it through each of the two holes on the outside of the door. Then twist the wires together to tighten them and fix the door.

Install the Plywood

Install the plywood in the door's opening by using the measurements you took. Change the header of the frame (top) and the sill. Use a level to make sure that there is no slop between the sill and header. If it isn't perfect you can place a second shim wherever required and repeat the process until the sill and header are even.

Once the plywood has been put set, secure it with the stainless-steel hinge bolts and wingscrews. Make use of a screwgun that has an attachment for hex heads to avoid stripping off the heads of the screws.

If you live in a house with studs that run along the length of your doorway, you can drill hanger bolts into each of the framing members. This is much easier than using a drywall saw to make the hole.

After you have installed the plywood, measure the width and the height of the door opening. If necessary, trim your bottom of the plywood to fit the height of the door frame. Cut two pieces of framing lumber 1 by 6 to serve as braces for the upper and lower ends. Wear eye protection and cut along the lines that are marked on the plywood with circular saws fitted with a fine-toothed knife. Splinters can be removed from the cuts by using a sanding device.

Once you've got the two braces in place, nail each one to the plywood with pairs of finishing nails 2 inches long. southampton boarding up doors sink all the nail heads after you've finished. Make sure to seal the braces and the plywood with a high-quality wood sealer, like this wipe-on polyurethane by Minwax.

If the door is too large for your doorway, you can add an ornamental molding to fill in the space between the jamb and the door or alter the size of the opening. In many instances, however it is less expensive and more convenient to buy a new door. It also removes any problems that you might have experienced with your door's original model even if it was damaged or not suitable for the opening.

Read More: https://www.repairmywindowsanddoors.co.uk/southampton-emergency-boarding-up-near-me/