Notes

15 Gifts For That Boarding Up A Door Lover In Your Life
How to Go About Boarding Up a Door

The protection of vacant investment properties from the elements is attainable by boarding up a door. It may not prevent every damage, but it can help to prevent some of the problems associated with severe storms.

The idea of boarding up doors and windows can also deter burglars, vandals, and squatters. However, it can be expensive and time-consuming to install plywood boards over the openings on a house.

Measure the Door

The first thing you'll require is tape measure. You may want to keep a ladder or chair close to hand in case you need an improved view of the top of the frame. Wear gloves and safety glasses in the event that you need to use these tools.

Once you have the measuring instrument, start by taking the door width measurement. You can do this by running the tape measure horizontally across the door. Make sure to remove any extra parts of the door, for instance a sweep, when measuring. Then, determine the height by measuring from the floor to the sill or lintel. It is essential to take measurements in several places, particularly when measuring doors older than they might not be a perfect rectangular shape. If the measurements differ, use the largest number.

After you've taken the width and height measurements, you'll need to determine what size boarding you'll need to fit into the frame. It should be at minimum 2 inches larger and 1 inch taller than the door. 2'' higher. This will allow plenty of room to shim the frame and door into place.

When you're ready to take the door frame's width and height measurements It's recommended to remove any trim or casing around the door jambs so you can see the studs that are behind them. This will enable you to determine the exact distance between the studs of the frame and the edge.


Once you've removed the trim, you'll be able to determine the dimensions of the frame of the door by running the tape over the entire frame in three places and using the smallest measurement as the width of your door. Also, you should determine the height of the frame from the top to the bottom on both sides, and then use the shortest measurement as your door's height.

If you're having difficulty with the measurements, seek out a professional who will come to your home and take the measurement. They will tell you what size and type of door you require and how to prepare your frame to accommodate a replacement door.

Cut the Plywood

A door frame is typically made of a series of thin boards or studs that create an open space around the door. A typical door is secured by two hinges that are attached to these studs. If you want to finish doors, you'll need to remove it from its hinges over night. Placing plywood into the door's opening is a great way to board a door and prevent insects from gaining entry into the home. This is easy to do without having to nail or screw the plywood to the door frame.

Plywood is cheap, easy to work with and looks fantastic when finished. This makes it the perfect material for temporary solutions to a problem that requires removing an existing door and finishing or installing a new one. It is also a great option to secure the opening of a room that is being renovated, like an unfinished basement or construction site.

For a wall constructed of plywood, start by measuring the width and height of the door opening. Make notes using an utility blade and a straight edge made of metal like a drywall or a square. Then, snap the chalkline along each line to indicate where you want to cut. Use a circular blade to cut the plywood into the required size.

It is crucial to shield your eyes and ears when cutting plywood. Wear protective goggles or earplugs if possible. It is also important to use a blade with a lot of teeth, that will allow you to cut quickly and with minimal tear-out. Utilize a small piece of wood to guide the blade. Keep it a hair's breadth away from the line you are cutting.

An effective way to hold the plywood in place without gluing it to the studs is to attach two braces at each end. Put one brace side that is inside and the other one on the outside of the door. Then, insert the deck screws into each of the holes and tighten them with an open-end wrench.

Fasten the Plywood

It's time to attach the frame to the panel once you have the plywood sheet cut to the proper size and the holes for rails and stiles of the door frame have been predrilled. This is a simple task that doesn't require any advanced carpentry skills if you use the correct tools and follow the right procedure.

Begin by setting up a workstation near the doorway with two sawhorses and a 2-by-4 frame lumber at each end of the table. Lay the entire sheet of plywood flat atop the sawhorses, using the marks from the measurement process as a reference for cutting. Utilize a utility blade and a metal straight edge to score the lines. boarding up bury-st-edmunds will create a guide for the saw blade and keep the wood from splintering when cutting the plywood.

Wear eye protection and use a circular or table saw with a blade that has a fine-toothed edge to cut along the line of scoring. Then sand the edges the plywood panel using 120-grit sandpaper to smooth the panels and remove any burrs that may have formed from the saw cuts. After sanding then apply a wood sealer and allow it to dry according to the manufacturer's instructions.

Install the hinges onto the door frame. If you're using a T-hinge drill holes in the outer side of your door to accommodate the straps of the hinges. Then, put the hinge's outside on its mark and screw it to the frame with a screw gun. Repeat the procedure for each hinge on the interior of your door. Be careful not to overtighten them, or the door may shift.

If you have a single hinged T on your outside door you can make it easier to close by placing wire through the loops on the outside hinges. Fold a piece of make a half-way tie, and then thread it through the two holes on the exterior of the door. Then, you can twist the wires together and secure the door.

Install the Plywood

With the measurements you made, place the plywood in the door opening. Shim the header (top) of the frame and the sill (bottom). Utilize a level to make sure there's no slop in the header or sill. If it's not quite right then put a second shim where needed and continue this procedure until you've got the sill and header to be in a straight line.

Once the plywood is in the frame, secure it with stainless steel hinge bolts and wing nuts. It's a good idea use a screw gun with an attachment for a hex-head to avoid stripping the head of the screws.

While you're at it, should your home be constructed with studs running across the width of your doorway make holes for hanger bolts in the plywood and into the framing studs. This is a much easier task than drilling the hole with the aid of a drill or drywall saw.

After installing the plywood measure the width and the height of the door opening. If necessary, trim the bottom of the plywood to fit the dimensions of your door frame and cut two pieces of framing lumber as braces that attach across the upper and lower ends of your door. Put on eye protection and cut along the lines marked on the plywood using a circular saw equipped with a fine-tooth blade. Splinters can be removed from the cuts by using a sanding tool.

After you have the braces set attach each one to the plywood using a pair of finishing nails that measure 2 inches. When you're finished counter-sink the heads of all the nails. Seal the braces with a good wood sealing product, such as the wipe-on polyurethane by Minwax.

If your door is too large it is possible to add decorative molding to fill in the gap between your door and jamb, or you can reduce the size of your opening. In many situations, it's more affordable and easier to simply find a new door. It also solves any issues you may have had with the door you originally purchased in the event that it was damaged or was not fit for the opening.

Here's my website: https://www.repairmywindowsanddoors.co.uk/bury-st-edmunds-emergency-boarding-up-near-me/