Notes

The Reasons Why Replacing Upvc Window Handles Is The Most Sought-After Topic In 2023
Replacing uPVC Window Handles

Switching the handles of windows made of upvc is an easy job. It is essential to ensure that the replacement handle fits inside the spindle cutout in the window mechanism.

If the steps below are followed properly If you follow the steps correctly, any cockspur handle can fit most windows. The most important thing is the step size of the handle.

What to Find

Over time, uPVC handles on many windows in the UK may begin to show signs of wear and tear. When this occurs, the handle could become shaky or difficult to operate, making it necessary to replace it. This is a relatively easy task that can be accomplished by anyone who is comfortable with basic hand tools.


The first step is to make sure that the handle is securely fixed to the window frame, and is in a position that is open. The next step is to find the fixing pins or screws that keep the handle in position. They are usually located on the inside face of the handle and are removed with a screwdriver or pliers.

Once the handle has become loose it can be taken from its hinges by gently pulling it off. It is then necessary to locate a replacement handle that is the same design and size. This can be done on the internet or at the local DIY store and the process should only take around five minutes using an screwdriver.

When replacing the handle on a uPVC handle it is essential to consider the step height. This is the distance from the bottom of the handle to the point at which it sits on the frame of the window. This is a standard measurement and you should confirm the height of the step prior to ordering an replacement handle.

There are a variety of sizes based on the kind of handle. Inline handles for uPVC windows usually have lug centres of 31mm as well as handles with cockspur with 43mm centres. Tilt-and-turn handles are commonly found on uPVC Windows. They feature a unique design that lets the window be slid down to let in air, and then turned to fully open the window.

The most frequent breakage in uPVC handles is that they crack inside instead of breaking away from the base section. This can make them hard to open and is why it is important to make sure that any replacement handle you buy has the same length of spindle as your existing one.

Remove the Old Handle

If your window handles are damaged or improperly fitted, they could cause double-glazed windows to open and close incorrectly. They may even get stuck. This could be due to many factors, including general wear and tear on the metal handle or corrosion. In these situations it is essential to seek replacement window handles made of upvc immediately in order to prevent further damage and loss of functionality.

When replacing upvc windows handles, you should remove the handles that were previously installed from the window. To do this, begin by taking off the screw that is covered when the handle is in its closed position. Repair My Windows And Doors will reveal a screw, and once it is removed, you can then begin to remove the handle itself. It is a good idea to use an electric screwdriver for this, as it makes the task much easier and quicker.

It is also worth noting that the screws on the handle may be hidden behind plastic caps, so it is recommended to take the Stanley knife to the screws and take them off. After the handle has been removed, examine the square cut out on the handle's base to make sure that the new window lock handles are compatible with it. This is crucial as you'll need to determine the length of the spindle on the old handle to ensure it is the same size as the window mechanism and handle spindle cut out.

There are three types of upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles with two screws, and Spade handles which have flat arms and can be used on either side of the upvc window. It is simple to replace the handle when you have found one that is suitable. Simply screw it into place, and ensure that the spindle is correctly inserted into the lock mechanism. After that, you can you can tighten the handle onto the window frame. Your replacement upvc handles will now be secured.

Take a measurement of the Spindle

If you're looking to replace a handle made of upvc that has fallen, it's likely that the spindle that holds it in place is damaged or loose. In some instances, this could be fixed with a screw or pin to secure it. In some cases it might be necessary to replace the handle. There are many kinds of window handles made of upvc. There are three types of handles: inline espagnolette tilt-and-turn, and cockspur. Each type has a different procedure for installing and replacing the handle.

It is essential to measure the current handle before purchasing a replacement. This will ensure that the new handle is the right size and will fit correctly within the window. All handles are sized in accordance with industry standards, so it is easy to identify the correct size.

To determine the size of your handle first remove it from the window by turning it back to the open position. You will then be able see the size of the screw or pin that holds it. Use a ruler or tape measure to determine how long the spindle is. Once you have determined the length of the spindle you can buy a new one that is the same length.

When buying a replacement, it is important to take into consideration the step height of a upvc window handle. The step height is measured from the base to the point where the handle is placed on the frame. Typically, this will be approximately 21mm for uPVC windows, and 9mm for aluminium. To ensure that the new handle will work, you can drop something in the gap to see how far it goes before it comes into contact with an obstruction.

Cockspur handles may have different backsets based on the kind of window you want to install them in. Inline Espag handles have an average height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets based on the window they are located in. This is because they have a spur that extends from the handle and locks onto a cockspur wedge hitting plate.

Install the New Handle

After you've chosen the new handle, align it carefully with the holes for screws on the door. Secure it using the screws supplied. If you're replacing the latch lever the lever can be mounted the same way as the main door handle. Finally, reattach the door trim in order to conceal the mounting screws and finish the project.

Tips: To remove a metal head from a wedge made of wood, place the handle on the floor, so that its wide end is on the floor. Then use a hammer and tap the narrow end. Be careful not to scratch the handle or the handle spindle.

Website: https://www.repairmywindowsanddoors.co.uk/guildford-door-handle-repairs-near-me/