Notes

10 Startups That'll Change The Skoda Key Reset Industry For The Better
How to Reset a Skoda Key

Just got a message from my infotainment system to say that the battery in the key is low and must be replaced. This isn't the first time, and last time I went to an auto shop, they replaced the battery for free in two minutes, and they said it would be working again.


Switch ignition ON and secure the vehicle mechanically. Press the unlock button 5 times in intervals of 1 second on the remote control. A short horn will sound.

EEPROM Method

It could take some time for a professional car locksmith to reprogram your keys if it stops working. In most cases the EEPROM is analyzed to discover the unique code of the car. This is a risky procedure because there's a high possibility that the information stored in the module will be corrupted. It's best to leave this to a skilled locksmith.

An EEPROM is a non-volatile memory utilized in a variety of electronic devices, such as keys for cars. It stores information that includes the unique authentication codes and encryption keys that your vehicle recognises when you use it to unlock or start the vehicle. These codes are crucial because they inform your car that you are the owner of the key and that you have permission to drive.

If your EEPROM is damaged it will cause the keys to not work. The issue is typically caused by using the incorrect key, or hitting the wrong buttons. It is possible to reset the key by using an instrument that is specifically designed for this purpose. However this approach may not work. It is recommended to employ an expert with extensive experience in programming automotive keys.

To reset your EEPROM, you must first remove the Kessy module from the vehicle. This is the module that sits above the accelerator pedal on the left-hand side of the vehicle. Take off the clip made of plastic that is holding it in place using the help of a screwdriver. Then, disconnect the electrical connectors. Take it out. Then, you can read the EEPROM data with an SOIC8 clip or micro pincers connected to a programmer. Once you have all the information you can save the file and write it back into the EEPROM.

To read the EEPROM data, use a program like PonyProg and click Read Device. The EEPROM dump will appear as an array of hex characters. There are three distinct Hex values: the KEY_CODE, the key_count, and the V_ARG_ENABLED. You must change all the other Hex values to 00 to "virginize" the chip. After you've done this, you can flash the chip to restore its function.

Ignition Method

This method requires activating the car's system with an additional key. It might not work for all cars however, it is possible to reset the key fob in cases where it's not working or the battery has died. It should also work in the event that the buttons are hit hard (a common reason for this is people trying to press down the unlock button a few times).

This method requires that you turn on the ignition and keep it turned on. Then, mechanically lock the door to the driver's compartment with another key. Then, rotate the key fob to its lock position, and aim it at the receiver for transmission situated on the front of the car above the mirror. Press and hold the unlock button for a couple of seconds. The horn will sound, and the key fob should begin to function.

If the skoda key isn't working, the transmitter inside may have been damaged or unsynchronized with the vehicle's anti-theft system. This will require reprogramming. A technician or automotive locksmith can assist you in this.

If the key fob isn't working after reprogramming it, you could be able to determine that the car has "forgotten" the key (if the vehicle hasn't used in 6 months). This should still allow you to try a resync method in the user's manual - take off the driver's door lock cap and lock, then open the car with that key. It should re sync the key, but if it doesn't, it's time to visit the dealer. skoda spare key is typically the case for keys that are no longer working and takes less than 2 minutes.

Keyless Entry Method

The latest generation of keyless entry systems - like the type that is used in modern OCTAVIA and ENYAQ iV cars - features one ingenious safety feature that stops thieves from "signal extension". A signal is sent to the car and then to the key, which must respond within a certain time. If the key fails to respond, the vehicle will not be unlocked and it will sound alarms.

A sensor located in the handle of the door can also be used to inform the car that the key is nearby. It works by sending an electrical signal to the internal coil inside the key, which then transmits the signal back to the sensor. If the sensor detects this, the car will unlock itself and may switch on the interior lights if it is set up to do so.

Even older keyless entry systems have an old-fashioned backup. If the remote does not work, you can open the door of the driver mechanically by sliding out the blade or, in certain models, by pressing down on a button within the door pocket. This method is particularly helpful when the battery of your key is dying or you've lost it.

Remote Control Method

If you've recently purchased an electronic remote control but it isn't working in your vehicle, the seller might not have programmed it to match your vehicle. It could also be that the terminals of the battery are loose (look for this, they may feel a bit loose to the touch and may be soldered in the wrong place) - carefully soldering them back in place will bring your key fob back to full working order. If you're not confident with this kind of repair, contact an expert auto technician.

Turn off the ignition, and lock the vehicle from the inside using the second key that's not compatible (this resets the memory position 1). Enter channel "01" (may be channel "21" in some Audi models). Insert the new key fob in the door of the driver and then press its unlock button twice within 5 seconds (often enough to reach the next available memory position).

Repeat this process for up 4 additional remote controls. Be sure to turn off the ignition in between programming each remote. You should hear a sound each time you successfully program the remote.

Here's my website: https://www.thekeylab.co.uk/skoda-car-keys/