Notes

Fitting a Cat Flap
It might seem daunting to put up a cat flap however, with the proper guidelines, it's not all that difficult. Find out how high you'd like the cat flap (normally it's at the belly height). Mark this point on your door and use the included template to help you drill.

If you have a kitten who is still a newborn, gently prop the door slightly open and invite it to go through. Reward it when it goes through.

Take a measurement of the door

A cat flap is a great method to allow your pet to come and go into and out of your house as it pleases. This can help with keeping your cat healthy by making sure that it is exercising as well as being able to come back in if stuck outside in bad weather, particularly during the winter. It can also reduce the amount of time you have to allow it in or out and will also help ensure your home is secure by allowing you to be aware of when it went out.


However, it is essential that the flap on your cat is fitted correctly to prevent your pet from being able to escape through it or be pushed through by any other animals (e.g. dogs). It is crucial to determine the height of your pet's belly as well as the entrance to your home to ensure that the flap is at the right height. upvc door panel cat flap can adjust the height of your flap in case your cat is taller or smaller than average.

The next step is to make use of a spirit level to mark the center of the door, where you will be installing the flap. With the markings as a reference, use a jigsaw and cut out the shape of the flap in the door. After cutting the area and sanded the edges to create smooth surfaces. Drill any necessary holes.

The process of installing the cat flap isn't as difficult as you think and it should not take more than two hours for the entire task from start to the end. The process can be slightly more challenging if you need to put it in the case of a uPVC door or composite one. This is because composite doors come in different thicknesses, which could affect the way the holes are cut. This is why we recommend hiring an expert to do the task, especially if you have never worked with glass before.

Measure Your Cat

You can avoid hours of listening to the pet's meow to be let in or out. This is particularly helpful when your cat is in the house during all seasons while you are at work.

It is essential to measure your cat's measurements first before you begin the installation. It may seem like a simple task, but it's essential to measure your cat correctly. Otherwise, your pet may find it difficult to use.

Firstly, make sure your cat is calm and not anxious prior to taking the measurements. You will have to hold your cat in a place where they cannot move. Also, ensure that the measuring tape is straight and not bent against the body. Keeping the measuring tape or ruler against their body from the top of their head to the bottom of their tail will enable you to get an precise measurement.

Once you've got the measurement of your cat, it is time to take a look at the door and decide where to put the flap. It is advisable to position the flap on the highest point of your cat's stomach as this will help them to move through it without much effort. This will also stop the flap from making a lot of noise as it swings back and forward.

You will need to think about the thickness of the uPVC or composite door, as well. While all timber doors have a similar thickness to them, uPVC or composite doors are different in their overall design. This makes fitting an enclosure for your cat more difficult as you must ensure that the hole is the proper size.

You can make use of the template included in the instructions to mark the location of the opening on the door. This will help you determine where the hole must be located and make sure that the template is positioned properly on the door. It is also a good idea to employ a spirit-level to ensure that the template is placed in a straight line against the door.

Cut the Flap

Before you can install your cat flap, you'll must cut the door panel in order to make it large enough for it. It can be a difficult task, so it's recommended that you get a professional assist you if you do not have the expertise or experience. You can also read the instructions that come with the kit to discover how to do it correctly.

To do this, you have to measure the height of your cat or kitten's belly. Use this as an indication point. A good guideline is to place the flap around 10-15 centimeters from the ground as this is the typical height of the cat's belly. This will allow your cat to pass through the flap without difficulty and will make it difficult for other cats or naughty neighbours to get inside or out.

Draw the location of the cat flap on the door using a pencil. Next, if your kit has a template for paper, place this over the door and use the marks to drill holes into every corner of the template. Then, you should be able cut out the design of the template and replace it with your cat flap.

You can install your cat flap yourself inside a wood or uPVC door when you're confident with the Jigsaw. Ensure that you do not cut into any of the door's mullions, or vertical rails. You can use a jigsaw cut the panel into a square or circle according to the design of your cat flap. Make sure to take your time and don't try to make the jigsaw cut faster.

Once the hole has been cut, carefully place the cat flap into its new place of residence. Make sure it is securely secured. If it has caps on the screws, then place these caps onto the protruding screws. Once the screws have been installed, sand the rough edges and then apply sealant to any gaps. This will block draughts from entering your home.

Fit upvc cat flap door panels

If you have an ordinary cat flap, you can encourage your pet to go through it by placing a small amount of cat food on the top of the door. You can also try pushing the cat using a stick or your hand. Once your pet is used to walking through the flap it will be able to move into and out as it pleases and you should be able to let it in or out without having to be there holding the door open for it all day (and potentially in any weather).

You can install a cat flap into an UPVC or glass door although this may not be as simple as fitting one into a timber external door since UPVC and some glass doors don't have the same thickness. This could have a significant impact on how you cut the hole for the flap, and will also affect whether the flap will fit properly once it's been put in place.

Depending on the type of cat flap you pick, it may be equipped with a mounting kit and template that shows you exactly where to drill holes for it. If the kit doesn't include the template, you can photocopy it to create your own. It is important not to press the jigsaw too hard when cutting, so that it doesn't leave a bigger than necessary hole in your door.

Some cat flaps come in circular shapes, which are more difficult to install. If you have a circular flap, it is essential to ensure that the hole is in the correct position on your door because if it's not, your cat can't use it and could be stranded outside all day (or even at night).

Some models of cat flap have locks that let you manage the time your cat comes and goes. This is useful for pets who are afraid of going out in the dark, or coming back in the dark. They can also be useful when you are working all day. The lock can be turned on to allow or deny entry, and some can be locked in either direction which allows you to close the door completely. This is especially helpful for cats with a chronic illness or older age who aren't willing to go out in rainy weather.

Website: https://leach-salomonsen.technetbloggers.de/cat-flap-installation-into-glass-1730918072