Notes

This History Behind Ghost Immobiliser Install Will Haunt You Forever!
Autowatch Ghost Immobiliser Installation

The Ghost is the UK's most advanced aftermarket immobiliser for the CAN bus. It's subtle, doesn't have LED indications or key fobs and is concealed in the wiring of the vehicle.

The user can also disable the system temporarily using Transport Mode when renting out their vehicle. This guide will take you through the installation process of an Ghost immobiliser.

Professional Installation

The Autowatch Ghost immobiliser is a cutting-edge security device that protects your vehicle against hacking, key cloning and relay attacks. The system connects directly to your car's ECU and is secured by a unique PIN code that you can choose. It is not detected by thieves using diagnostic scanners or other advanced methods. It isn't able to be disabled with circuit cuts.

The system is simple to use, however it's essential to use a an expert installation to ensure a clean and secure connection to your vehicle's ECU. An approved installer from Thatcham can assist in the installation and programming of your Ghost system. They can also recommend a tracking or alarm system to complete the protection package for your vehicle.

The first step is to disconnect your battery in order to avoid the possibility of airbag deployment and short circuits. Once the battery is disconnected, the installer may be able to work safely. Basic hand tools are useful for securing connections with precision and a multimeter may be used to verify electrical values and safety. Cable ties and insulation tape are also vital for protecting connections and keeping wiring tidy. The user's manual offers specific instructions specifically tailored to your Ghost Immobiliser model.

It is crucial to select an area for grounding that is free of any paint or debris during installation. Installers should also ensure that the immobiliser's wires CAN H and CAN L are connected to the proper ECU ports. Based on the model, these wires might need to be soldered or plugged into. To ensure a secure and long-lasting connection it is recommended you choose a top-quality plug.

Transport Mode can be turned on by the customer once the installation is completed. This permits mechanics or valet parking to access the vehicle without knowing the pin code. To accomplish this, the user must hit the service button on the dashboard five times in a matter of 2 seconds. After this is done the system will verify by displaying 5 signals.

The Autowatch Ghost 2 is a highly effective immobiliser that's TASSA verified and Thatcham approved. It's a smart choice for anyone who frequently rents their vehicle through platforms such as Turo. An immobiliser can cut down on insurance costs, since it decreases the likelihood of theft.

Getting Started

If you are looking for a solution that will protect your vehicle from thieves, you can't go wrong with an autowatch ghost immobiliser. The device stops your car from starting the case that someone steals or copies your key. It's possible because of its advanced technology that prevents the engine from starting until the correct PIN code has been entered.

The device connects to the vehicle's bus network, CAN which allows direct communication with the ECU. It makes use of buttons already on the dashboard and steering wheel to create a unique sequence that only you know, making it impossible for anyone else to start your car. This is the best way to safeguard your pride and joy. It will keep its value intact should you ever decide to sell it.

Installing an immobiliser from Ghost is simple, but you must follow the directions to avoid electrical problems and system malfunctions. First, you have to locate and determine a constant 12V power source and a good grounding point on the vehicle's chassis. After that, you can begin to connect the wires for the immobiliser. Make here are the findings of high-quality connectors and soldering techniques to ensure an effective connection. Also, ensure that you insulate the connections by using heat shrink tubing or insulation tape to protect them from electrical short circuits and other problems.

Once the wires are connected, you can plug in the battery and begin the engine to check whether the immobiliser is functioning. When everything is functioning correctly then you can put it in a safe location under the dash or elsewhere in the vehicle. Be sure to conceal it well to ensure that thieves cannot tamper with it.

The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) certified This means it complies with the highest standards of security and is a fantastic deterrent to car thieves. It offers superior protection against key cloning, hacking and relay attacks, and can't be disabled without knowing the code. The device is also simple to use and can be set into an auto valet mode so that your vehicle is not activated when you bring it in for maintenance or an MOT.

Wiring

The Ghost Immobiliser is a cutting-edge security system that is designed to stop theft of vehicles. It connects directly to your car's CAN bus network and communicates with the ECU, making it virtually undetectable to your vehicle. In contrast to other aftermarket systems that require the removal of circuit components The Ghost Immobiliser does not interfere with any of the factory settings of your vehicle.

The system is also undetectable by thieves using scanners for diagnostics. This is because the system doesn't transmit and receive radio frequency signals, and it uses CAN data to communicate with your ECU. It doesn't require any modifications to your existing key fobs.

Enter your disarm sequence (either two or one button) and turn on the ignition of your vehicle to use Ghost Immobiliser. The indicator will flash two times to confirm that you've entered the correct code. After that, you are able to start your vehicle and drive off safely.

Once installed, the Ghost Immobiliser will secure your vehicle from key cloning and hacking, while protecting the value of your most prized possession. If you ever need to surrender your car to valet parking or for service The Ghost Immobiliser can be temporarily disabled in Transport Mode.

You'll need a constant power source (12V) as well as an earthing point to complete the installation of the Ghost immobiliser. Be sure that they are well-insulated and safe to touch. Cable ties are also suggested for bundling and securing the wires. This will reduce the risk of theft by thieves. Be sure to check the exact location of these points to avoid mistakes and mark them with the help of tape or a label. Check every connection for signs that they're getting worn out. Make sure all connections are firmly in place, and are properly sealed. Make sure to test your Ghost Immobiliser after the installation is completed. This will make sure that the unit is operating correctly and that all connections are secure and insulated. Make sure to address any issues as soon as they arise.

Testing


The Autowatch Ghost Immobiliser is a cutting-edge vehicle security system that seamlessly into your car's ECU to prevent unauthorized engine start. Its cutting-edge technology safeguards your car from key cloning and hacking and other methods that thieves employ to steal cars. The Ghost works in conjunction with existing alarm and tracking systems to provide the best security for your vehicle. The Ghost's unparalleled features, paired with its discreet design makes it a sought-after choice for car enthusiasts as well as security-conscious drivers.

It is crucial to follow the procedures for installation to ensure a correct integration of the Ghost Immobiliser. A good starting point is to consult the wiring diagram for your vehicle that will serve as a roadmap for locating and connecting the necessary wires. You'll need to determine the power and grounding sources. Once you've located them, you'll be required to mark the points to make them easily identifiable when installing. It is essential to use top-quality materials and tools. Hand tools are essential to help you make precise connections. A multimeter can verify electrical values and guarantee safety. Cable ties and insulation tape can help keep connections neat and tidy. Also, a user's guide will provide specific instructions tailored to your Ghost model.

It is crucial to test the system before installing it. Enter the PIN code into the system, and then start the vehicle. This will ensure that the immobiliser works according to plan, and prevents unauthorised vehicle start-ups. This procedure should be carried out regularly as part of your routine inspections of your vehicle to ensure the system is working properly.

Once the installation is complete After the installation is completed, you are able to drive your vehicle with confidence. The Ghost will safeguard your pride and joy from thieves who might steal your car. It will ensure that no one is able to escape with your car without having the correct PIN code. The Ghost can be used in conjunction with an approved Thatcham tracker that detects any attempts to steal or tamper with. This lets you locate your car if it's stolen.

The Ghost is compatible with a variety of automobiles, including those from most major manufacturers. Monty's Locksmith can help you secure your vehicle using this cutting-edge device. Contact us today to learn more about our service and installation options. We are a TASSA registered installer, which ensures that we adhere to strict standards in the installation of our products. This ensures customers, insurance companies, and law enforcement agencies that all installations are done safely and properly.

Here's my website: https://www.g28carkeys.co.uk/ghost-car-immobiliser-fitting-and-installation/