Notes

Membrane layer bioreactors for the manufacture of value-added items: The latest advancements, challenges and points of views.
The production of DFF from the real cellulosic wastewater was obtained with 118% yield based on 5-HMF conversion by HPMoV/meso-SiO2-NH2 (23) and oxygen, which was contributed to the one-pot conversion of sugar, furan and 5-HMF in the wastewater.Atmospheric coarse particulate matter (PM10) enriched with heavy metal(loid)s could pose potentially significant health risk to humans, while accurate health risk assessment calls for characterization of their bioaccessibility, besides the total contents. The health risk of major toxic heavy metal(loid)s in the PM10 from four large cities in northern China via inhalation was investigated based on their total contents and bioaccessibility. The annual mean concentrations of PM-bound Zn, As, Pb, and Mn in the atmosphere of the four cities were 650, 305, 227, and 177 ng⋅m-3, respectively. The levels of heavy metal(loid)s in the PM10 were generally higher in winter but lower in summer in all four cities, which resulted primarily from the emissions associated with coal combustion for district and household heating and the unfavorable meteorological conditions in winter. The bioaccessibility of heavy metal(loid)s in the PM10 ranged from 0.9 to 48.7%, following the general order of Mn > Co > Ni > Cd > Cu > As > Cr > Zn > Pb. CA77.1 Based on their total contents in the PM10, most heavy metal(loid)s posed significant public health risk via inhalation exposure in the four cities. However, after accounting for the bioaccessibility of metal(loid)s, the non-carcinogenic risk of most metal(loid)s was negligible, except for As in the PM10 of Jinzhong, while only the carcinogenic risk posed by Cr and As in the PM10 exceeded the acceptable level. These findings demonstrate the importance of characterizing the bioaccessibility of airborne PM-bound heavy metal(loid)s in health risk assessment and could guide the on-going efforts on reducing the public health risk of PM10 in northern China.Cyanobacterial blooms are a major problem in many lakes and can negatively impact public health and ecosystem services. The bioflocculation technique has proven to be a cost-effective, environmentally friendly technique with no secondary pollution to harvest multiple microalgae; however, few studies have focused on its effect on and potential for controlling cyanobacterial blooms in eutrophic lakes. In this study, the bioflocculation efficiencies of different Microcystis species under Glyptotendipes tokunagai (Diptera, Chironomidae) stress conditions and the interactions between secreted silk from Chironomid larvae and extracellular polymeric substances (EPS) from Microcystis were compared. The results indicated that G. tokunagai presented better bioflocculation efficiency on M. wesenbergii than on M. aeruginosa. The formation of "Large Algal Aggregate" flocs was promoted by the derived-soluble extracellular polymeric substances (i.e., proteins and polysaccharides, sEPS) from M. wesenbergii and silk from G. tokunagai. Both M. wesenbergii and midge silk had abundant functional groups, which was beneficial to the formation of the large aggregate. G. tokunagai secreted a large amount of silk to bridge with the sEPS of M. wesenbergii, forming a network structure via interaction between filamentous substance (i.e., complex of sEPS and silk) that plays an important role in the aggregation of Microcystis and the removal of the Microcystis biomass in the water column. The findings provide further insights that will benefit the existing efforts of combating Microcystis blooms in the water column via bioflocculation and will provide a new sustainable approach for inhibiting early bloom formation from the perspective of its provenance in the sediment-water interface.The disintegration of natural water sources signals out the scarcity of adam's ale and will be hurdle for the human physical state. So it is necessary to decrease waste loads and hence pressure on the ecology for the sustainability of fishery and dye industry. Herein, TiO2 nanoparticles doped with Sn and F are synthesized and the influence of simultaneous doping on the optical, surface morphological, structural, photocatalytic and antibacterial activities are investigated. Doping of TiO2 with Sn and F suppress the growth of both anatase and rutile phase because of the dissimilar boundaries. All the prepared doped and undoped samples are found to possess tetragonal structure. The influence of F and Sn in TiO2 lattice is recognized with the XRD and FT-IR spectra of the prepared particles The size of the obtained nanoparticles decreases as increasing concentration of F and Sn. TiO2 is showing the presence of spherical and ellipsoidal nanoparticles whereas doped samples showing nanobulk, pentagons and rods. The absorption edge of the doped samples are blue shifted with increasing concentration of dopants indicates the control of optical absorption property of TiO2. The visible light assisted photocatalytic degradation of fish processing waste water by doped and undoped samples are found to be established as 0.0076/min and 0.0071/min respectively. Visible light assisted degradation of commercially available dyes and fish processing waste water is assessed. Methyl blue showed enhanced photocatalytic activity under visible light irradiation compared to Methyl orange. It is observed that all the prepared particles show good antimicrobial activity against Staphylococcus aureus.The liquid level of a bioreactor is an important operating parameter governing the hydraulic retention time. In this study, a novel method is proposed to estimate the liquid level of anaerobic digesters. The proposed method has an advantage over typical differential pressure measurement as it considers the heterogeneity of the digestate along the level using multiple pressure meters. The real-time measurement generates a model to fit the densities at different liquid columns, predicts the density of the surface layer and determines the overall liquid level. A pilot-scale (0.33 m3 working volume; 1.2 m liquid level) digester, equipped with seven pressure meters, was operated to test the methodology. The performance of the digester was confirmed stable during a long-term (175 d) operation. A set of density-pressure models was developed and were validated using the long-term experimental data. The new method employing cubic model showed significantly better estimation of the reactor level (mean error rate of 1.31%) with improved CDF, as compared with the traditional differential pressure method (mean error rate of 5.
My Website: https://www.selleckchem.com/products/ca77-1.html