Notes

Fitting Cat Flap in UPVC Door Panel
Cat flaps let your pet leave and come as they please without needing to let him in or out. They also help prevent your cat from toileting in the house.

upvc door panel with cat flap fitted is easier to install the cat flap on a Upvc panel than one made of glass, but you will require some knowledge and correct tools.

Measure the Door

Installing a cat door into a front door can be difficult however, as long as the cat flap is of the right type and you follow the directions it shouldn't be too difficult. We will show you how to draw the shape, then use a jigsaw to cut out the area in the door and then complete the job by securing the flap to the door. This will ensure the flap remains in place and also protects the doors from the damage caused by rain and wind.

To determine the size of the cat flap you need, measure the width of your pet. This will allow you to select a cat flap that is big enough for your pet to go into the house and exit without having to open the door each time.

If your kit has an illustration of where to drill, you can place it on the door, and then use a pencil around it. If your door has a sill or moulding at the bottom, make sure that you leave enough space between your cat and these elements.

Set a square to make sure you are cutting correctly and to ensure the hole is a good rectangle shape. Once you are happy with the result, you can start removing the remaining door material. Use a set square to ensure that you're cutting the material properly and that the cut is a rectangle. When you are satisfied with the result, you can take the door material off.

Draw a Line

The cat flap lets you to let your pet in and out without having to worry about unwanted visitors or unwelcome gifts. It also stops draughts and keeps your home's temperature stable. The installation of a cat flap your door may seem daunting for those who haven't attempted it before. A lot of people will hire a professional carpenter or joiner to complete the work. It is an option, but you can do it yourself, provided the tools are in order and the directions are followed.

Although this is much simpler with a wooden door, it is still possible in uPVC doors - although you need to be very cautious not to damage the doors since this could invalidate your warranty. First, you must take measurements of the door to make sure it will accommodate the new cat-flap. If you have a standard uPVC panel it should be a breeze. However in the case of made of composite or another kind of door, you might need to be more careful.

Next, you will need to determine the height of your belly for your cat. This is the distance from the floor to the underside of the cat's stomach and you'll need to locate a place near the door that will be within the range that your cat is able to comfortably walk through. Once you know this, you will need to mark out the area with an eraser and a spirit level to ensure that the hole you make will be suitable for your cat.

Once you've marked the area, it's time to make the hole. It is essential to take your time and use a jigsaw ensure the cuts are smooth and clean not rough and uneven. This could cause damage to your door. Wear safety glasses and a dust mask when using a Jigsaw. Inhaling sawdust is dangerous for your health. After you have finished cutting the hole, you will need sandpaper to smooth the edges so that the cat flap is easily fitted into place.

Cut a hole

Getting a cat flap fitted to an existing door panel or double glazing sealed unit can be quite difficult. It is tempting to do it yourself, but unless have expertise in DIY, it's recommended to hire a professional in to do the job for you. A mistake in the process may not just be ugly, but also a security risk as well as allowing cold air to enter when the cat is outside and hot air to escape inside.

Mark the hole position on the door with a pencil and spirit level. This will ensure it is correctly positioned and aligns with the rest of the door. Make sure you have some sandpaper to smooth out any rough edges.


Once the line has been traced, you must cut the hole with a jigsaw. Be sure to wear the appropriate safety equipment for working with a power tool. If you are concerned about the noise of the jigsaw, you can purchase one that is cordless, which is quieter and simpler to use.

It is crucial to only cut away the material that is required for the fitment of the cat flap. A little bit of extra material will be required for the thickness of the the flap but removing more than that could cause issues and harm the frame of the door.

A upvc door may include a metal frame, or panel which could block the microchip cat flap, and if this is the case you'll need to make an oversize hole so that the metal doesn't touch the wall of the cat flap, if this is done it is crucial to fill in the oversize gap and seal it with water.

If you're installing an animal flap to an upvc door or a double glazed window with a metal frame, you'll need to speak to a specialist who can supply you with a new glass pane with the hole for the cat flap already drilled in it. It is cheaper to do this instead of trying to install a cat flap into an existing glass pane that was not designed specifically for this purpose.

Install the Flap

Cat flaps let your pet come and go whenever they want, allowing them the freedom to relax inside the house when they're feeling like it. If you have an uPVC front door, it might be difficult to put in a cat flap. This is especially the case if you do not own an glass panel that can be cut. If you are willing to install a half-glazed uPVC replacement panel, it is possible to add the cat flap. It's not as easy as making a hole in the door, however there are some things you'll need to take care of first to ensure it's safe.

A uPVC, GRP or composite door panel usually has an extremely thin plastic outer skin that is bonded to a soft, insulating polystyrene core. It is crucial to be cautious when cutting the material. This kind of door typically has a template which you can use as a reference to cut the hole in the door.

After you have carved out the hole in your front door, it is time to put in the cat flap. You can purchase and install many different models, from basic push-button operated models to microchip activated units that allow access only to your pet. No matter which type of cat flap you pick it's essential that your cat is able to use the flap without getting stuck in bad weather.

It's a good idea to select a circular fitting rather than a square one, as circles are more securely cut into door glass. It's because square holes are more likely to crack the glass when they're drilled. It's also a much safer option as you're not at risk of drilling into toughened glass that could shatter and cause injury to your pet or your family. This is especially crucial if you have a child or elderly person at home who could be injured by shards glass.

Homepage: https://fry-merritt-2.federatedjournals.com/window-with-cat-flap-1729790433