Notes

Fitting a Cat Flap
The process of installing a cat flap may seem intimidating but it's easy to do with the proper instructions. Firstly, determine how high you would like the flap to be (on average or belly height). Note this on your door, and use the included template as a guide when drilling.

If you have a kitten, or a young kitten you can prop the door open a bit and gradually allow it to pass through. Reward it each time it goes through.

Measure the Door

A cat flap is a great way to allow your pet to come and go inside and out of your home whenever it likes. This can help keep your cat healthy as it will ensure that it is exercising regularly and be able to return inside if it gets trapped in the elements during bad weather. It also can reduce the amount of time you'll have to allow it out or in and can keep your home safe by allowing you to be aware of when it went out.

It is crucial that the cat flap is correctly fitted to prevent your pet from being able to escape through it or be pushed through by any other animals (e.g. dogs). It is important to measure the height of your pet's stomach and the width of the doorway in your home to make sure the flap is at the proper height. If upvc door panel with cat flap is longer or taller than the average, you can alter the position of the flap by moving it up or down a small amount.

The next step is to make use of a spirit level to mark the center of the door that you will be installing the flap. Using the marking as a guideline, you can use the jigsaw and cut the shape of the flap within the door. After you've cut the area out and sanded the edges to create smooth surfaces. Make any holes that are required.

Installing a cat flap ought to not take more than two hours. The process can be slightly more challenging if you need to put it in the case of a uPVC door or a composite one. This is because composite doors come in different thicknesses, which can impact the way that holes are cut. We always recommend to contact a professional for your first experience working with glass.

Measure Your Cat

A cat flap will save you from hearing your pet's cries for you to let it in or out. This is especially helpful when your cat is inside in all weathers when you are at work.

It is essential to first measure your cat before you attempt the installation. It might appear to be a simple task, but it is essential to measure your cat correctly. In the event that you don't, your cat may find it difficult to use.

First, make sure that your cat is calm prior to taking measurements. You'll need to keep your cat in a position in which they cannot move. Also, ensure that the measuring tape is flat and not curved against the body. By keeping the ruler or measuring tape against their body from the top of their head to the base of their tail will allow you to get an precise measurement.

Once you've got the measurement of your cat, it is time to take a look at the door and decide where to put the flap. The flap should be placed at the level of your cat's belly. This will allow them to go through the door with minimal effort. This will also prevent the flap making a lot of noise as it opens and closes.

You should think about the thickness of the uPVC or composite door too. While all doors made of timber have a similar thickness to them, uPVC or composite doors are different in their overall design. This makes fitting a flap for your cat more difficult, as you must ensure that the hole is the right size.

You can also use the template included in the instructions to mark the location of the opening on the door. This will allow you to see the location where the opening should be and also make sure that the template is properly placed on the door. Utilizing a spirit level to check that the template is flush against the door can be extremely helpful.

Cut the Flap

You'll need to make an opening in the door to accommodate your cat flap before you can attach it. It's a challenging job and it is recommended that you hire a professional to assist you if you do not have the skills or experience. You can also consult the instructions included in the kit to find out how to do it properly.

To do this you need to measure the height of your cat's or kitten's belly and use that as an indication point. A good rule of thumb is to set the flap of your cat about 10 centimeters off the ground, as this is approximately the average belly height for cats. This way, your cat will be able to move through the flap without difficulty and also give the other cats or neighbours who are snooping an issue when trying to leave or enter.

Mark the position of the cat flap on the door with a pencil. If your kit has a template, place it over the door. Use the markings on the template to drill holes at every corner. Then, you'll be able to cut the template and replace it with the flap for cats.

If you are installing your cat flap in an entryway made of wood or uPVC, you are able to do it yourself if feel confident enough to handle a Jigsaw. Be careful not to cut through the mullions or rails that run vertically of your door. You can use a jigsaw to cut the panel into a circle or square, depending on the design of your cat flap. Be patient, and don't try to force the jigsaw to cut faster.

Once the hole is made and the flap is firmly positioned, carefully place the flap of cat food into its new location and make sure that it is securely secured. If it features caps for screws, then put these onto the screws that protrude. Once the screws have been installed then sand the rough edges and then apply sealant to any gaps. This will stop draughts from entering your home.

Install the Flap


If you have a standard cat flap, you can help your pet through it by placing a small amount cat food on the top of the door. You can also push the cat with a stick or your hand. Once your cat has become used to walking through the flap it will be capable of walking through the flap whenever it wants. This will allow you to let it in and out whenever it wants.

You can install the flap onto an UPVC or glass door but it's not as simple as fitting one into a wood exterior door due to the fact that UPVC and some glass doors don't have a consistent thickness. This could have a significant impact on the way you cut out the flap's hole and whether the flap will fit correctly after installation.

The mounting kit could include a template that shows you where to drill holes. If the kit doesn't include the template you can copy it to make your own. When cutting, it is important to keep the jigsaw from being pushed too hard so that you don't create a larger hole than you need in your door.

Most cat flaps are square or rectangular in shape, however there are also some which are circular and these are generally more difficult to place. If you have a circular flap, make sure the hole is in the correct place on your door. If not, your cat may not be able to access it, and might be locked outside for the entire day (or at night).

Certain models of cat flaps have locks which permit you to manage when your cat comes in and goes. They can be extremely useful when you're concerned about your cat going out at night and coming back in because of the darkness, or you're at work all day. The lock can be used to allow or deny entry, and some can be locked in both directions, allowing you to shut the door completely. This is especially helpful for cats with a chronic illness or older age who don't want to go out in bad weather.

Read More: https://valueoval65.bravejournal.net/how-to-choose-a-cat-flap-installer