Notes

The Reasons Replacing Upvc Window Handles Is Harder Than You Imagine
Replacing uPVC Window Handles

Switching the handles of windows made of upvc is a fairly straightforward task. It is important to make sure that the new handle is a good fit for the spindle that was cut out of the window mechanism.

If you follow the steps below any cockspur handle can fit on most windows. The most important factor is the step height of the handle.

What to Look for

A large portion of windows in the UK come with uPVC handles and, over time, they may begin to show signs of wear and tear. If this occurs, the window handle can become loose or difficult to operate, making it essential to replace it. This is a fairly simple job that can be accomplished by anyone who is comfortable using basic hand tools.


The first step is to make sure that the handle is securely fixed to the window frame and in an open position. The next step is to find the screws or pins which hold the handle in place. They are usually located on the inside face of the handle. They can be removed with a screwdriver, or pliers.

Once the handle has become loose and sagging, gently pull it back from its hinges. Then, you'll need to locate a new handle in the same style and size. This can be accomplished online or in the local DIY store and it should take about five minutes with an screwdriver.

When replacing a uPVC handle, it is important to think about the step height. This is the distance between the handle's base and where it sits within the frame of the window. This is a typical measurement, and you should verify the height of the step before purchasing the replacement handle.

There are various sizes depending on the type of handle. how to replace upvc door handle are available for uPVC windows with lug centres of 31mm, while cockspur handles have centers of lugs of 43mm. Tilt-and-turn handles are commonly found on uPVC windows. They feature a unique design which allows the window be slid down to let in air and then rotated to fully open the window.

The most frequent uPVC handle breakage is internal cracking instead of a break at the base. This can make them hard to open, and it is therefore important to make sure that any replacement handle you buy has the same spindle length as your existing one.

Remove the Old Handle

Incorrectly installed or damaged window handles may cause your double-glazed windows to open or close in a way that isn't correct and may cause them to become stuck. There are a variety of reasons for this including general wear and tear or corrosion of the metal handle. In replacement handles for patio doors is essential to replace the window handle as soon as you can to avoid further damage or loss of function.

One of the first things to do when replacing upvc window handles is to remove the old handle from the window. Start by removing the screw covered with the handle when it is in a closed position. This will reveal a screw that once removed, you are able to begin to remove the handle itself. You can make the process easier by using an electronic screwdriver.

It is also worth noting that the handles' screws could be hidden behind plastic caps, therefore it is recommended to take an Stanley knife to the screw caps and then take them off. After removing the old handle, you will need to check the square cutout on the base to make sure that the new handle for the window lock is compatible. This is crucial as you'll need to measure the length of the spindle on the old handle to make sure it is in line with the size of the window mechanism and the handle spindle cut out.

There are three kinds of Upvc handles: Espag handles with a central screw that can be turned either left or right and Cranked handles with two screws, and Spade handles which have flat arms and can be used on either side of the window made of upvc. Once you have a suitable replacement, it's simply a case of screwing the handle into position and ensuring that the spindle is inserted into the lock mechanism. Once this is done, it should be tightened to the window frame and the replacement upvc window handles should be secure.

Take a measurement of the Spindle

If you have to replace a Upvc handle that has fallen, it's likely the spindle that holds it in place is damaged or is loose. In certain situations it is possible to tighten the spindle with pins or screws. In some instances it might be necessary to replace the handle. There are a variety of upvc handles. They include espagnolette handles that are inline as well as cockspur handles. tilt and turn handles. Each handle type has its own method of installing and removing the handle.

It is crucial to measure the handle before buying a replacement. This will ensure that the new handle is of the correct size and fits into the window. Fortunately, all handles follow industry standard sizing so it's relatively easy to identify the correct size.

To determine the size of your handle first, take it out of the window by turning it to the open position. You should then be able to see the size of the screw or pin that is holding it. Then, use a tape measure or ruler to determine the length of the spindle. Once you have determined the length of the spindle, you can purchase a new one that is exactly the same size.

When you are looking to replace a handle window handle, it is crucial to consider the step height of an upvc window handle. The step height is the distance from the bottom of the handle until where it sits on the frame. This is usually about 21mm or 9mm for aluminum and uPVC. To make sure that the new handle will work it, you can drop something into the space to check the distance it will go before meeting an obstruction.

Cockspur handles usually have different backset heights depending on the style of window they are installed in. Inline espag handle heights are 43mm from centre to center (two fixing points). Cockspur handles have different backsets, based on the type of window they are in. This is due to the fact that they have a spur that extends from their handle and locks onto a cockspur wedge striking plate.

Install the New Handle

After you've chosen the new handle, ensure that it is aligned with the screw holes on the door. Then secure it using the screws provided. If you're replacing the latch lever, it can be installed the same way as the door handle. Then, attach the door trim to conceal the screws for mounting.

Tips: To remove the metal head from a wedge made of wood, place the handle on the floor, so that its wide end is on the ground. Then, use a hammer and tap the thin end. Be careful not to damage the handle or spindle.

Homepage: https://telegra.ph/A-Productive-Rant-About-Replacement-Window-Handle-10-16