Notes

15 Gifts For The Repair Car Keys Lover In Your Life
How to Repair Car Keys

The car keys aren't big and might not seem to be important, but they're essential for the operation of your vehicle. Replacing a traditional or a transponder one could cost as much as $200.

There are ways to fix your car keys yourself at less than the cost. This article will address the most frequent car keys problems and their DIY fixes.

Dead Key Fob Batteries

Cars are equipped with remote key fobs that makes opening the doors and trunk easier than ever. However, the battery inside this device can die. There are, however, a few tricks that can be used to solve this problem in a pinch.

Check to see if your car is still in the ignition mode. If it is, the key fob battery may be drained instead of dead. To test, press the button on the fob against the ignition button on the vehicle. If it does not work, the battery is probably fine and only has to be replaced.

To replace the battery inside the fob, pry the case open using an screwdriver. Be careful not to press too hard because this could cause the fob to split in two. If the fob doesn't seem to be coming open easily, try wedge your pry tool in several places on the outside of the case.

Open the electronic portion of your vehicle after you have removed the mechanical key. Then, insert the battery replacement and then snap the shell together. If how to repair car key fob won't work after this, there could be a larger issue with your car's remote start system that requires a professional diagnosis. A trusted mechanic will be able help you in this situation. If you need help with your car, you can contact roadside assistance.

Broken Key Ring

There are a few steps to do if your key fob doesn't work because the ring has been broken. Check to see if you can find the broken piece in the ignition. If it's still there, remove it without damaging either the ignition lock or the door lock. Contact a locksmith if have difficulty getting rid of the key. They have tools that allow you to safely remove the damaged key from the ignition.


A broken car key can be caused by corrosion of the plastic frame or circuit board. You can clean the circuit board using a cotton swab soaked in rubbing alcohol. This will get rid of the corrosion and stop damage to the contact pads.

You can repair a damaged rings by using a thick wire or nail to seal the hole. Superglue can also be used to repair a damaged ring. After cleaning the ring using a damp cloth, apply a small amount superglue to each end of the nail or wire. Press the pieces together and let them dry prior to using your car. These DIY solutions may seem appealing, but they're only temporary solutions. For remote car key repairs -term repairs, it's best to hire an experienced locksmith. They have the tools and know-how to fix a broken car key quickly and effectively. They can even replace the battery inside the key fob and change it's programming if required.

Broken Key Blade

Some key blades break due to a lot of wear and tear. If this happens, it's probably time to purchase a new key. The issue isn't as serious as you think at first glance. The primary issue is that the metal blade has snapped away from the case.

One way to fix this is to spray the key hole with a lubricant. Then, you can use pliers, tweezers, or a pin to grab the broken end of the key and pull it out. You may also make use of a magnet if the key is magnetic. Just be careful not to use a magnet on an ignition key because it could cause the tumbler of the lock to break.

If you are unable to remove the broken piece from the key, contact a locksmith right away. They have tools that let them safely remove keys without causing damage.

Super glue can be used to fix the snapped lock. Apply a small amount of glue to the edges of the break and press them together. Wait until the glue dries before you insert your key into the lock. But this method isn't very reliable and you might have repeat the process several times before it is successful. In addition the super glue may not be enough strong to keep the key in place. Therefore, this is more of a stopgap measure rather than a permanent solution.

Broken Plastic Loop

If the plastic loop is damaged it can render the key ineffective. This is a simple fix. For a replacement, you can use wire that is thick or a finishing nail. For each end of the nail or wire you need to drill two holes into the plastic loop. Cut the wire or nail to the desired width, and place one drop of superglue in each hole. Then, press the wire or nail into the holes to seal them and allow it to dry.

Another option is to purchase a replacement shell from a locksmith that sells them. They can remove the programmable part of your key, move it to the new shell and cut the new blade for less than a full replacement cost.

This isn't the best solution, but will allow you to travel once more if your key split in half. It can be difficult to fix the key blade if it is in the ignition. You could try using a hair clip, a needle or an extractor tool to pull the broken part of the ignition, but it's risky if not careful. The best solution is to call a locksmith with special tools for safely removing broken keys from the ignition. They can also make you new keys with the appropriate cuts for your vehicle's ignition to ensure that it functions correctly when inserted into the lock.

Broken Master Key

You'll have to attempt at regaining the key before it becomes completely destroyed. There are a variety of methods that you can try, such as using lubricants, tools, needle nose pliers and tweezers to take a small piece of the key that has been broken and then remove it.

To start, spray the inside of your lock with a lubricant like WD-40 or graphite powder. You could also try the hacksaw blade method, which involves gently moving the blade down the side of the broken key, and connecting to a few of the 'teeth' - if you succeed in doing this you should be able take the broken key from the lock.

Another helpful tool is an extractor for keys spiral, which you can find in many hardware stores. This tool has a thin rod with spiral threads that can be placed in the keyway, and later bent into the broken part of the key. Once it has gotten caught on the serrations, you can turn the bar in a circle and then pull it up against the broken part of the key.

Before contacting a locksmith, try to remove the broken master key before calling a locksmith. If you're not able to take the broken piece off then you'll have to contact a professional locksmith. Locksmiths can create you a new key that can be programmed using the transponder of your car.

Homepage: http://nutris.net/members/breadcelery7/activity/1942428/