Notes

12 Stats About Upvc Door Handle Replacement To Make You Seek Out Other People
Choosing the Right UPVC Door Handle Replacement

It's easy to replace your upvc handles however choosing the best handle can be a challenge. Modern double-glazed handles are equipped with spring cassettes, but older handles don't.

If the upvc handle of your multipoint lock is loose and floppy, there may be an internal problem. This article will address the various possible issues & their causes.

Sagging or drooping handles

uPVC handles are susceptible to wear and tear. this post is particularly true in older properties. A broken spring cassette inside the door lever is the most frequent reason for a handle that is floppy. This is due to excessive force, and the square spindle that holds the cassette may be dislocated or turned round.

The good news is that replacing the door handle with uPVC is a fairly simple task and can be accomplished in a matter of minutes. The first step is to remove the handle unit that was previously installed by removing the fixing screws that are visible on the back of the lever plate. Once the handles have been removed you can remove the cassette from the square spindle and replace with an entirely new one.

You can find a wide selection of uPVC door handles to select from online and many of them come in different finishes. The finish you choose will determine the durability of your handle as well as how it will be easy to clean. Finishes such as PVD, Stainless Steel or Resista are made to withstand corrosion and will last for up to 25 years.

After you have selected a colour or style, you are able to select the type of handle that you need. The most popular kinds are lever and pad arrangements. Lever pads feature an inside lever and an outside paddle and are often employed as a security measure to block access by unauthorised persons.

Then, take a measurement and note the dimensions of the handle you currently have. You'll need the PZ dimension (the distance from the screw hole to the center of the lever) and the length of the handle, and the size of the keyhole. You can compare these measurements to the size matrix of the handle to find the appropriate replacement.

Broken springs

Over time, handles made of uPVC can become wobbly or loose. The spring cassette could also break. The springs are used to ensure that the lever is in a horizontal direction. Without them, your doors will not lock properly.


Modern uPVC handles are designed with these cassettes directly built into the backplate. However, older uPVC doors typically contain these springs within the lock mechanism. It's not something you can do by yourself, but it's worthwhile to have your locksmith examine the situation as this could be the reason for the sagging uPVC handles.

The most frequent issue with uPVC handles is that they loosen over time. This is usually due to worn out springs, which are easy to fix. Most often the reason for this is excessive use of the handle, and because of that the square spindle inside the handle will wear away, causing the springs to be displaced.

To fix this you will need to open the door and unscrew the fixing screws at the back of the handle plate. This can be done using a Philips screwdriver. Once the screws are removed the handle can be taken off. The plates for the handle are then able to be gently taken apart. Then you can take off the springs that were in use and replace them with new ones.

Depending on the type of handle you are using the distance between the two screws can vary and this is crucial to know prior to buying an alternative. This measurement is referred to as the PZ measure and it is recommended that this is measured using an accurate tape measure in order to be accurate.

After replacing the springs you should be able operate the handle with no issues. It's worth lubricating the internal mechanism to ensure that everything is working exactly as it should. This will ensure that your uPVC door is as secure as can be, and also increase their comfort as time passes.

Handles that slide around

Handles that slide around can be caused by a variety of reasons, but one of the most frequent causes is when the levers on the handle aren't aligned properly with lock. This can happen on both uPVC and composite doors, however it is typically more evident on older doors as they are usually made of cheap materials that aren't able to hold up to the elements.

A professional can fix this issue by re-aligning the handles to ensure they are in line with the lock. They will also check the lock to determine if anything requires fixing. In many cases, a simple modification to the springs of the handle is all that's needed to fix this issue.

It's simple to replace your uPVC handle however, you must take measurements of the handle you have to ensure that the replacement is the correct size. You will need to measure the distance between the two screws, the size of the keyhole and lever, as well as the distance between them. Then, you can utilize this uPVC handle size guide to locate the correct replacement for your home.

After you have made the measurements, you can remove the existing uPVC handle. It is usually a simple process and only requires a screwdriver. Once the screws have been removed, you can then unscrew the handle itself and then proceed to install the new handle.

Before starting the work, you should ensure that the door is secured open using a wedge to stop it from closing in the middle of your work. After you remove the handle, you will be able to inspect the components underneath the door that cause the door to slide.

A handyman from Fantastic Services will be able to help if you don't want to do the work yourself or aren't confident enough. They'll employ locksmith techniques to unlock the door without causing any damage and will then replace the damaged handle and make sure that everything is in place and working as it should be.

Gearbox damaged

A damaged gearbox may cause the handle made of upvc to become stiff and lose its function. The lock could also not be able to be opened with the use of a key. This could be dangerous and must be addressed as quickly as possible. It is important to call a locksmith if you cannot resolve the problem yourself. They have the tools and expertise to do the job right.

The first step is to remove the handle from the cover plate. This can be done using a screwdriver equipped with flat heads. After you have removed the handle, remove the middle screw which holds the cylinder. After you have removed the middle screw you'll be able loosen the two screws that hold the barrel. You can then pull the barrel out of the door. To do this, you will require someone to prop the door wide open.

After removing the cylinder, you can replace with a new cylinder. Make sure the new cylinder is the same size as the previous one. In the event that it isn't, you could end having a handle that isn't aligned properly. This could lead to various issues such as leaks and draughts.

A lot of door handles made of upvc have slots for adjustment. These slots can be used to tighten or loosen the handle. These slots are usually found on the inside of the doors, near the spot where the handle meets with the cylinder. The slots for adjustment can be tightened by using an allen wrench. Once you've made the necessary adjustments, you can screw the handle in and put it back in place. Then, you can test the handle to make sure that it is working correctly.

If the door handle made of upvc becomes floppy or loose when closed, it is typically a sign that the upvc gearbox has broken down or internal spring components are breaking down. This could cause your upvc multipoint locks to fail, leaving your door wide open to intruders. If this occurs, it will be necessary to replace the upvc gearbox. This will cost between PS145-PS280 including labor.

Read More: https://www.repairmywindowsanddoors.co.uk/folkestone-door-handle-repairs-near-me/