Notes

4 Dirty Little Secrets About Change Door Lock And The Change Door Lock Industry
Reasons to Change Door Lock

There are many reasons to change the lock on your door, from increasing your home's security to redecorating your entryway. It is also possible to change locks if your key gets stuck or is difficult to turn.

DIY novices can also modify their lock. Get upvc window locking mechanism repair need to begin.

Remove the old lock

Before installing a new lock it is important to take out the old lock from the door. This is essential if you suspect someone else might have a key to the house. It's an excellent idea after you've moved into your new home, suffered a break-in or a roommate moved in. It is simpler than you think and can be completed in just a few minutes.

Start by removing the screws that secure the deadbolt faceplate on the door frame. You'll have to take off the screws on both sides of the door in order to remove the faceplate. This will let you see the hidden screws and give you an understanding of how to continue with the remaining steps.

After you have removed the old faceplate, you'll have to take off the bolt and strike plate. Use a screwdriver to loosen the bolt, and then take it out of the hole in the door. If the bolt is rusted, you may need to use a chisel or hammer it. When using a chisel to remove the bolt, make sure to not to scratch the door frame.

Make sure the new deadbolt, doorknob, and lock will fit into the holes that are already present in the door before you remove the old one. Most hardware stores and big box stores offer different kinds of locks. They can assist you in choosing the best one for your requirements. If the lock you bought isn't the right one for your door.

Find small depressions or notches in the handle and around the trim while you take off the lock. If you can find them, insert a straightened safety pin or flat screwdriver through them to open the handle and expose the screws beneath.

After removing the screw from the handle, you can start removing the knob. To do this find the set screw at the knob's base and loosen it. Next, you will need to remove the knob from the spindle. Finally, carefully remove the spindle from the door.

Install the new lock

It's a great idea to change the locks on your doors frequently, especially if you have been the victim of a break-in. It's an affordable, simple and effective method to ensure that your home is secure. With a screwdriver, and a few basic instructions, most people can handle it themselves. You might also want to learn how you can change the lock's key to ensure that only you have the key.


You will need to purchase a new lock that has the same keyway as your current lock. Most locksmiths will rekey your lock for you for a fee however, you can save money by doing it yourself. You can purchase a new lock from hardware stores or on the internet. Standard deadbolts will fit most doors. However, you will have to measure your door to ensure it fits.

The majority of the time your new lock will include an image of a cardboard model that shows you how it will fit on the door. This template can be used to drill the hole. It's much simpler than measuring every time. If the template doesn't match your hole, take it back to the shop and request a replacement.

When you install the new lock, you must ensure that it is placed on the right side of the door. You can verify this by looking at the latch, which ought to be marked "up" or something similar. Make sure the latch is properly placed on the latch plate, then secure it using the screws supplied.

If you are replacing the knob lock on your door, it's also important to be aware of the way it's operated. Some knob locks are right-handed. If you're not paying attention, the knob could be placed on the wrong side of your door, which would hinder it from locking either from the inside or outside.

After you're done, you should test your new lock to make sure it's working. It should be able to lock and unlock the door with keys from inside as well as the outside. If you're not satisfied with the results you can always contact an expert locksmith to fix the issue.

Test the lock

A door lock that will not unlock can be annoying, but it can also put the safety of your family at risk. It's easy to fix the majority of problems with door locks by performing some troubleshooting, and lubrication. Make sure that the key is properly cut and the lock assembly isn't loose or dirty. If this doesn't solve the issue, try lubricating your door lock actuator using graphite powdered.

Check that the doorlock switch, wiring harnesses, and actuator connector all work properly. To do this, consult the manual or wiring diagram to determine the purpose and color-coding of all door lock switch wires. Then, test the wires using a light or digital meter to determine whether the door lock actuator receives power and ground when the switches are turned on. If you see voltage switches that toggle with each other, it means the switches are in good shape and the actuator is likely to need replacing.

If the switch seems to work however the actuator does not move when you turn the knob it could be an issue with the cylinder itself. The actuator cylinder is fitted with pins that have a spring-loaded. They prevent the cylinder from turning until the key is inserted, which then pushes them upwards to match the height of the key in that area. Then, the cylinder to turn and unlock the lock body which allows the handle to latch.

If the door lock actuator is inoperable, you can remove the switch and wires from the actuator with a small screwdriver to release the locking bolt and remove the plastic cover which holds the electrical connector. Then, disconnect the door lock actuator and let it fall. Then you should be able to identify and remove the two 10mm bolts that hold the actuator in place. After the actuator has been removed then you can disconnect the black electrical connector.

Replace the key

If your deadbolt that is keyed or door knob is not working, you'll have to reset it or replace it. This isn't difficult and can save you money. It is best to have an expert locksmith inspect the locks for any problems prior to starting. This will give you peace of assurance that your home is secure and safe.

To begin, remove the exterior faceplate from the deadbolt or doorknob. There may be screws holding it in place, you need to remove them, use a screwdriver to loosen them and pull the faceplate away. Next you can use a flat-head screwdriver to remove the interior faceplate. After you have removed the faceplate you can pull out the bolt and screw from the lock cylinder.

A locksmith can determine whether you need to replace or rekey the lock. They can also give you advice on the best security solutions for your home. They will also make any necessary modifications to the door and frame to ensure a perfect fit. They also offer the guarantee for their work.

You need to purchase a new lock key before you are able to change it. It is crucial to use a key that fits well in the lock. A key that is not the right size may harm the internal mechanism of the lock and hinder it from working. Insert the key into the lock to test its size. If it is flush with the plug, it's the right size. If the pins protrude out of the top of the plug, they're too long.

There are many reasons you may want to change your door lock, for example:

Rekeying locks is a cheaper option than replacing it if you are moving into the home of an owner who has passed away or if keys have gone missing. It's also more cost-effective than a complete replacement. Rekeying an existing lock might not be feasible in some circumstances. If the lock has been damaged or jammed repeatedly, for example it could be the right time to replace it.

My Website: https://www.repairmywindowsanddoors.co.uk/weymouth-window-lock-repairs-near-me/