Notes

Replace Door Lock Isn't As Tough As You Think
How to Replace Door Locks

Replacing the door lock could be a tricky task. It is essential to protect your home from potential intruders and also to change locks if you have an additional housemate or have let out your home.

Most new locks are designed to fit standard door widths. If your door is thicker, you will require an "thick door" kit that has larger screws and a larger tail piece for the deadbolt.

The old lock can be removed

You will need to remove the old lock from the door before you install the new one. This can be done with the help of a few tools, but be careful not to harm your door or frame. Using the right tools will save you from costly repairs in the future.

Begin by taking out the screws that support the handle and trim. This can be accomplished using the help of a screwdriver. After the screws have been removed, you can take the trim off. You can then get to the screw that holds the trim and handle to the door. After you have removed the screw and lock cylinder and open handle.

One of the most obvious indications that your lock is getting old is when you are unable to longer turn the key inside. This is because the tumblers wear out and then stopping the movement upwards or downwards, causing the lock to stop working. If this happens, you'll have to take the lock to a locksmith for it to be reset-keyed.

Begin by removing the screws holding the faceplate in position. If the kit you purchased does not include new screws, you can purchase them at an hardware store. If you're installing a mortise lock you should also remove the screws that hold the external rose plate to the door. After removal of the screws, take off the plate and dead bolt.

Next, search for a pinhole on the inside of the handle. If you spot one, slip straightened safety pins into it. You can also employ a flat screwdriver press against the depression. This should open the lock handle and expose screws that can be removed in order to remove the entire lock from the door.

Fitting the new lock

If you're looking to replace your lock following a break-in or simply want to improve the appearance of your door, installing a new lock is relatively easy. However, it's important to measure the door to ensure that you purchase a new lock that is the right size for your door. This is particularly important for deadbolts that require a specific size to fit into the strikeplate and bolt pocket. Contact your local hardware store for assistance if you aren't sure what measurement to take.


If you're replacing a mortice, use the existing centrerail as a guide to position the new mortise. Once you've determined the location of the lock, you'll need to drill holes along the central line of the same size as the lock. Then, chisel away wood until you have a neat rectangular space for your mortice lock to sit in. After that, insert the lock and outline the faceplate with a marking knife. Mark and drill screw holes to secure the faceplate.

You can save money when changing locks by purchasing an initial set that includes an re-keyable key as well as an unlocked key. The kits are available at numerous online retailers, as well as home improvement and hardware stores. They also include a set of instructions to help you complete the task.

If you're renting, be sure to review your lease agreement before changing locks. It could require you to provide the landlord with a key to the new lock. If so, you may be required to dismantle the old lock and replace it with a new lock. You can buy a basic lock at your local hardware store, or you can buy a smart lock that connects to your home's Wi-Fi and lets you lock and unlock your door from afar. A good choice is a Schlage Smart Lock, which can be used with a variety of door levers and knobs. This system can also be linked to your smart home security hub, allowing you to receive alerts when your door is opened or locked.

Installing the new lock

A damaged lock poses an issue for security, so it's important to replace it immediately. It's easy to replace a door lock. The first step is to remove the old lock. The screws that hold the lock in place are removed and the lock is removed. You may need a screwdriver or Allen wrench, depending on the kind of lock you have. Save all the components of the old lock and put them in a secure place.

Then, insert the new lock into the door. Most kits come with a cardboard template of how the lock should be placed on the door. If the template doesn't line up with your door you can trace the template with a pencil, or use a chisel remove any extra material. After the new lock is installed, ensure that the latch plate's interior is aligned with the mortise lockset hole to ensure a secure fit.

When you install the new lock, make sure not to tighten it too much. This can cause the lock to rattle, or even break. If you have a keyed lock make sure the spindle is aligned with the knob's hole. If it isn't you can make use of a screwdriver to push the spindle into the lock and into the knob.

After you have completed installing the new lock, you can now install the base plate that is included with it. If the lock doesn't come with a base plate with a design then you can purchase one that is compatible with the hardware.

The last step is to test the new lock to ensure it functions. This can be done by inserting the key into the lock and turning the lock so that it opens. If this doesn't work, you need to seek out a locksmith.

You can also avoid burglaries by having a professional change the locks' keys. This is a process that involves changing the lock's internal tumblers so that it will not accept the old keys. This will help you to feel safe and secure at home.

Testing the new lock

Installing an entirely new lock is a great method to make sure that it functions as intended. This is why it's essential to follow the guidelines carefully. You may not be able open your door if don't. You can contact an expert locksmith for help if you are unsure of what to do. A locksmith can provide advice on the best locks for your house.

If you're having trouble opening your lock, it may be a problem with the latch or handle. Try lubricating your latch with graphite or spraying it with WD-40. This may fix the problem. You may need to replace the latch if it is damaged. latch is not working properly.

The lock could have been installed incorrectly. The inner door handle clip can be broken or not present on the new lock. In this case it is recommended to grab the handle from the inside and then insert an additional plastic retainer clip. The handle is then linked to the lock and the lock tested.

After you've changed the lock, it is important to test the keypad to make sure that it's functioning correctly. You can test the keypad by inserting it into the lock and turning it. If the keypad is functioning properly, your door should be able to open and lock.

It is also advisable to check the deadbolt lock to determine whether it's working properly. If it's not working, take off the latch on the door and remove the Phillips-head screws. Replace repair upvc window lock that was installed with the new one. Be sure to align and load in the deadbolt lock in the correct way.

Spindle testing is another way to test a new lock. It can be performed by inserting a screwdriver in the spindle. This test should be carried out before re-installing the lock to prevent any mistakes during installation.

Website: https://www.repairmywindowsanddoors.co.uk/bournemouth-window-lock-repairs-near-me/