Notes

<h1 style="clear:both" id="content-section-0">MODEL SM-6490H in Mesquite Texas</h1>


Press RESET buttons b. OPEN draw takes care of (DOWN) for 10 to 15 seconds to ease pressure in cyndrical tubes a b 8 10 Cleansing: 2. Dismantle NOTE: Prepare dishwashing area before disassembly, utilize container to momentarily save large eliminated parts and also a small container for O-rings, and also have a towel close by to record excess water.

2. If maker has air pumps, dismantle them 1. Transform power switches OFF a. OPEN draw manages to verify absolutely no pressure in cylinders; twist air tube adapters to unlock and also disconnect air tubes 1 b. Take air tubes apart entirely; each air tube has O-rings (3 ), adapters (2 ), as well as check shutoff (1) c.

Rotate suction tubes to unlock and also eliminate suction tubes, springtimes, and stoppers out of air pumps; watch that springtimes wear t fly out e. Take suction tubes apart entirely; each suction tube has O-ring (1 ), springtime (1 ), and stopper (1) f. Unscrew screws on air pump housings; separate air pump covers from coverings g.

Eliminate giving door 3b a. Get rid of dispensing-door hand-screws (4) b. Remove dispensing door assembly from cylinders 9 11 Cleaning: 2. Dismantle 4. Dismantle giving door a. Get rid of beater overviews (2) from door assembly; get rid of gaskets (2) from door setting up utilizing O-ring elimination device 4a 4b 4b b. Remove prime plugs (2) from door assembly; eliminate O-rings (4) from prime plugs utilizing O-ring elimination device 4c 4c 4d c.

139 Hover St, Longmont, CO 80501 - ZeroDown in Centennial Colorado
Featured Product Lines - Spaceman

Get rid of draw takes care of (3 ), lowering first to turn up draw valves, then taking out e. Eliminate draw valves (3 ), twisting while eliminating to protect against damages 4e 4f 4g f. Eliminate O-rings (4) as well as H-ring (1) from draw shutoffs making use of O-ring elimination tool g. Revolve celebrity caps (3) to make sure that tabs are obtainable; snap off star caps 5.

Eliminate beater settings up (2) from cylinders 5a 5b 5b b. Get rid of scraper blades (4) from beater settings up; separate scrape blade clips (4) from scrape blades c. Carry out beater footwear (4) d. Get rid of drive shafts (2) from inside cyndrical tubes utilizing a completely dry towel; different gaskets (2) from drive shafts 5c 5d 5d Keep In Mind: If you experience setting up difficulty with drive shafts, Spaceman uses a customized removal device for acquisition.

MODEL SM-6490H in San Antonio Texas
Get rid of internal drip tray and front drip tray + dash shield 12 Cleansing: 3. Clean All Components Care: Never ever wash parts in a dishwasher. Always hand-wash elements with safe, food-safe cleansers. 1. Verify power buttons remain in the OFF position 2. Make use of the big brush as well as awesome water to thoroughly clean inside the cylinders; make sure to scrub the back of the cyndrical tubes and also verify the cyndrical tubes are devoid of ALL item 3.

Gently clean as well as clean down the beyond the equipment 5. Carefully and completely clean all components removed from the equipment making use of supplied brushes, sponges, as well as clean towels; if device has air pumps, make sure to include all air pump components in cleansing 6. When cleansing the giving door setting up, tidy the priming ports with a little brush 7.

Verify all components are clean and complimentary of all food product prior to re-assembling device 13 12 14 Cleansing: 4. Assemble Care: Never ever compel the installment of any components. If parts put on t seem to fit, get rid of all components as well as repeat assembly.

Place drive shaft gaskets (2) on drive shafts (2) b. Seal gasket open areas with Spaceman lubricant, expanding onto drive shafts as well as preventing the top square components c. Insert drive shafts into rear shell bearings at the back of the cyndrical tubes, as well as transform them up until the essential engages securely into the outlet (when placed correctly, the drive shaft will no more turn 360) 3.

Sentient Equipment Design - OpenGovCO in College Station Texas
FSX, the Food Service Exchange, is the commercial food service industry's go-to source for purchasing overstock, discontinued, and scratch-and-dent equipment and supplies, and you will be shocked at how good our prices are (an average discount of over 50% of today's market price).
The FSX online marketplace provides restaurants, caterers, schools and other food service facilities with access to a wide assortment of products. The exchange allows for direct sales between pre-approved sellers and buyers, ensuring a seamless, reliable, and fast timely transaction process. Whether it is a model from a previous year or an item with a slight imperfection, buyers can purchase anything they need from our extensive pool of pre-selected, certified top equipment manufacturers and dealers. With Food Service Exchange, customers can expect premium equipment and supplies, amazing prices, timely shipping, and consistent satisfaction. Find out more information today about FSX Food Service Commercial Kitchen Equipment and Restaurant Supplies at 20 - 50% off market prices, with a minimum 90-day warranty. Plus, 5-star customer service reviews, unmatched 90-day warranty, and always free shipping!
Affix beater footwear (4) onto beaters (2 ); when properly put, neither footwear overhangs beater side 3b 3a 3c 3d b. Install scrape blade clips (4) onto scrape blades (4) c. Fit scraper blades onto beaters (2) d. Insert beater settings up into cylinders, making sure beater footwear remain in location; transform assemblies up until they involve the drive shaft secrets and also no more turn Install dispensing door 4a 4b 4c 4d 4e 4f 4g 4h 4i a.

Push prime plugs into holes in addition to dispensing door c. Insert attract valves right into giving door, O-rings-first; center draw valve goes in the middle as well as slots deal with outward d. Establish draw takes care of (3) right into ports on dispensing door, with modification screws facing down e. Slide retention pin via draw manages; secure with nut f.

Fit gaskets (2) into grooves on rear of door, level side out; slide beater overviews (2) over beater poles (2 ), with flanged edges against the door h. Insert giving door assembly right into cylinders, beater poles initially, pressing takes care of completely up as you put 13 i. Secure door setting up in a cross-pattern using handscrews (4 ), with the lengthy hand-screws (2) on top 15 Cleaning: 4.

The International Frozen Yogurt Association Is It Time to Repair or Replace Your Soft Serve Machine? - The International Frozen Yogurt Association

If equipment has air pumps, assemble and install them 5a 5b 5b 5c 5d 5d a. Place O-rings on back coverings, layer with Spaceman lube; install gears right into coverings (they only fit one instructions) b. Attach covers and also coverings, ensuring they fit flush; protect with hand-screws c. Location O-rings on suction tubes; gently lubricate O-ring locations d.

The Killers Concert Setlist at 1st Bank Center, Broomfield on ... in San Angelo Texas
Insert suction tubes right into pumps; turn to secure, as well as rely on desired overrun setup 5e 5f 5g 5g 5h 5h f. Coat air pump drive shafts with Spaceman lubricant g. Mount air pumps onto equipment: insert at an angle while pushing air pump in, slightly revolve backward and forward until the equipment engages the air pump drive shaft push in and revolve counter-clockwise to secure area h.

If equipment will go unused, set up air tubes right into receptacle, but do not link to air pumps; otherwise, set air tubes aside till after equipment has actually been keyed 6a 6a 6. Install hopper lids, agitators, and also drip trays a. Layer within agitators (if existing) with Spaceman lube and mount with arrow punctuating b.

If device will be left extra, mount air tubes and location receptacle covers on top; otherwise, established air tubes aside till after maker has actually been primed 14 16 Sanitization Sanitiza- IMPORTANT: After sanitizing the equipment, DO NOT wash or touch locations that have actually been disinfected. Product has to be added promptly. https://www.fsxmarket.com/FSX/c/1?query=:discount-desc:allCategories:1:manufacturerName:Spaceman

Sanitize machine before making use of once again. CARE: Always utilize food-grade, no-rinse sanitizer to sanitize. If cozy water is required to liquify sanitizer, allow the remedy time to cool down before including in maker. 1. Confirm setting up is full 2. If mounted, eliminate receptacle covers and also air tubes 3. Validate draw shutoffs are in the CLOSED setting (UP) 4.

Spaceman USA 6455H Service & Parts Manual in Paterson New Jersey
Allow service to fluster for 5 to 10 minutes; Never ever leave device on WASH for more than 10 mins 9. While agitating, carefully use a tidy brush to scrub and also disperse sanitizer option along hopper walls 10.

OPEN the draw valves (DOWN) and also drainpipe service from the device 12. Press RESET switches to stop cycle 17 16 18 Frozen Item Operation Add item to equipment 1. Confirm equipment has actually been lately sanitized (within 1 hr); if machine has not been recently sanitized, validate door hand-screws are tight, as well as execute sterilizing actions (Web page 15) 2.

Home - Spaceman

Area bucket or huge container listed below draw valve 4. Put 0. 25 gallons of item into receptacle 5. If equipment has air pumps, do not load product over little air inlet holes under of the air pump 6. OPEN draw take care of (DOWN); sanitizer will begin to spurt draw valve 7.

Pour remaining item right into hopper 9. Increase the prime plug on the top of the giving door until flow is 100% product 10. Push prime plug back down 11. If maker has air pumps: Press RESET, then press clean Make sure product is appearing of the large opening near the top of the air pump Press RESET 12.

Spaceman Email Formats & Employee Phones — Food Services in Richmond California
Mount air pump air tube, placing air tube into hopper, after that revolve as well as insert air pump connector into air pump; turn adapter to lock in place 14. Change receptacle lid keep in mind: The mix-low lights light up RED when a hopper is short on item mix as well as automatically de-illuminate when device is filled up.

Item is currently ready to ice up NOTE: Guidelines assume product is included one hopper at a time. Repeat steps as required 19 Frozen Item Operation Freeze product care: Never separate air pump (if present) with the device operating. If detaching air pump, initial press RESET to quit procedures and also open draw deals with for 10 to 15 secs to eliminate stress in cylinder.

Regarding Specialty Supply Strength Supply is one of the globe's leading carriers of icy yogurt makers and also soft serve ice cream makers.

Main compressor: 1x 6500 BTU, R404A Maker positioning needs CAUTION: The maker has to be placed on a degree surface away from wall surfaces as well as various other items. Clean as well as appropriately lube machine components prior to machine operation. Tune-Up Kit WARNING: If this is the initial time operating the equipment, you MUST clean and disinfect ALL parts prior to running the device. Carefully and completely wash all components eliminated from the equipment using provided brushes, sponges, as well as clean towels; if device has air pumps, be certain to include all air pump components in cleansing 6.

Read More: https://www.fsxmarket.com/FSX/c/1?query=:discount-desc:allCategories:1:manufacturerName:Spaceman