Notes

Exactly how to keep pellet mill die as well as roller?<br>
The roller as well as die are the using parts in a pellet machine. To make use of as well as preserve them in right method can reduce the failure price, improve the production, increase the functioning efficiency, save time as well as labor. If there is any type of issue in the roller and also die, the developing price as well as production would certainly decrease.



Load the die with oil combination

Whenever after making use of, or when you intend to change the die, bear in mind to feed oil blend (mixed sawdust as well as waste oil) to the pellet machine, eject all the biomass materials as well as load the die holes with oil mixture.



The biomass materials contains wetness, which would accelerate the rust of the die, and also cause it rough inside. The oil mixture completed the die doles will protect them from rusting or rust.



Replace the oil mixture every half a year

If you have leaved the pellet mill die aside for over a half year. You need to change the oil mix in the crave new, or they would set and obstruct the holes. This will affect the use for next time.



Resolve the block of the pellet mill die

If the die openings are obstructed and the wood pellets do not appear, we can use oil soak or cooking to soften the raw products, as well as make pellets once again. If this approach doesn't function, you can use drills to squeeze out the raw materials out, as well as feed oil products and also fine sand combination to grind the die.




Location the spare parts in best places

Protect the pellet mill dies in ventilate and completely dry area. If protected in moist area, they will certainly wear away quickly. If you do not utilize it for long time, you can coat it with a layer of waste oil to prevent deterioration of moisture in the air. Don't place the pellet mill die where the raw products are stored. The raw materials are simple to soak up wetness, which would accelerate the deterioration of the die.



Smooth the die as well as chamfer the die orifices


The holes on the pellet mill die are refined by high-speed gun drill, which has high level of smoothness. Check if there is any protrudes on the surface of the die, if so, smooth them with a flint glazing machine. If the die orifice are secured or have inversion, you ought to chamfer the die orifices and refurbish it.



Adjust the clearance between the roller and also die

In flat die pellet equipment, the suitable clearance between roller and also die is 0.1-0.3 mm. If the clearance is too tiny, the abrasion between the roller and also die will escalate. If the clearance is too big, the raw products layer will certainly be thick as well as the manufacturing will certainly decline. In ring chicken manure pelletizer , the suitable clearance is 0.1-0.4 mm.



Maintain the pellet mill die as well as roller tidy

When the timber pellets have actually worked for one month, you need to tidy up the roller and also die with diesel or gasoline. Coat livestock pellet mill with lubricant oil and install them once more. To guarantee consistent high production, we must keep the inside of the die clean.



If the ash is connected to the roller or the lubricating oil wants, the rollers would certainly revolve unsteadily, and the manufacturing rate will be affected. Users should inspect the functioning problem of rollers routinely.



Pre-heat the pellet device

Every single time before making timber pellets, feed the oil blend consistently till the temperature level inside is up to 50 ℃. Then you can feed the biomass materials to make pellets.



In wintertime, as the weather is cold, the die is sickly, we should pre-heat the machine for longer time, to make sure that the pellet maker can function better, the manufacturing is higher, and the life span is longer.



Ensures raw materials high quality

During the working of timber pellet maker, you need to guarantee there is no stones or irons in the raw materials, in case they trigger damage to the die.



The wetness web content in the raw materials ought to be 10%-18%. Dry product are difficult to mold and mildew, which will certainly intensify the abrasion of the pellet machine. If the raw materials are as well wet, the wetness would vaporize as well as combine with the wood powders, and obstruct the holes on die.


Homepage: https://www.blablaface.net/fertilizer-manufacturing-machine/