Notes

Safety safety measures for cnc tube bending machine
Our cnc tube bending machine has actually been mature and steady in regards to quality and innovation, so after acquiring the cnc tube bending machine, as long as you maintain it thoroughly and utilize it appropriately, the cnc tube bending machine can serve for a very long time. This article will present the security precautions and maintenance understanding of the cnc tube bending machine in daily use.

How to operate securely cnc tube bending machine?
( 1 )Check the surrounding of the work website and eliminate all sundries that hinder work and traffic. The ground ought to be tidy and no oil to prevent slipping. Work pieces must be stacked nicely and firmly to prevent collapse.

( 2 )Inspect whether the protective gadget on the cnc tube bending machine is in good condition, if it is not set up, it is not permitted to start up the cnc tube bending machine. The cnc copper tube bending maker needs to have great grounding and great electrical insulation, and the voltage should be stable.

( 3 )Inspect the lubrication points of television flexing machine cnc and add enough oil when there is lack of oil or no oil

( 4 )Examine whether the mechanical operation of the cnc tube bending machine for sale is typical and whether the electrical switch is sensitive throughout the trial run without work pieces. Start dealing with work pieces after validating that the cnc tube bending machine for sale works well. When 2 operators work at the same time, they should closely comply and coordinate. An operator needs to be designated to run the switch.

( 5 )When the cnc copper tube flexing maker is working, the operator should not leave the workplace.When the cnc copper tube bending maker is working, it is prohibited to get near to the pipeline flexing stroke variety. Warning signs must be set. Stand strongly when prying the tube to prevent being injured by the skid of the crowbar. Operators can only stand outside. Focus on the security around when adjusting television. Prior to using the hammer, please take in water for a couple of minutes to prevent the heavy hammer head from falling and hurting people. Do not wear gloves when hammering at television.

（ 6 ） In case of emergency situation when you run the cnc tube bending machine, please press the emergency stop button, then turn the switch to manual position, reboot it manually. If there is a fault, please report for repair work in time.

（ 7 ） Cut off the power supply of the cnc tube bending machine and do a great task of cleaning and lubrication after completing work.


Bottom line of day-to-day upkeep of cnc tube bending machine
1 、 Do not place the cnc tube bending machine in a place where the sun shines directly, to avoid the sun direct exposure which will cause the cnc tube bending machine to warp and break.

2 、 The table top of the cnc tube bending devices need to be kept as spick-and-span as possible. Do not stick tapes and other products on the table, and do not scribe on the table. If there is dust on the cnc tube flexing devices, please clean them with a damp towel and soapy water. Do not utilize alcohol, banana oil or other corrosive chemicals to clean the cnc tube bending makers.

3 、 If it is challenging to move the front and rear right-angle slides and the left and best rulers during using the cnc tube bending machine, please tidy up the dust and particles in the track and use 4B-B pencil cause doodle backward and forward on both sides of the sliding track and the lower guide rail of the moving plate, then the right-angle slides and the rulers can move efficiently.

How to reduce wear in making use of cnc tube bending machine ？.
1. The iron filings behind the guide rail of television bending device cnc need to be cleaned up regularly to make sure that the front and rear dust covers of the guide rail are intact. For the outlet track of the tube flexing device cnc, new grease needs to be added weekly to decrease wear.

2. Add grease to the securing cylinder bearing, securing cylinder and slider weekly or every 2 weeks.

3. Cleaning up and lubrication needs to be carried out every year for the rest of the bearings of the cnc tube bending machine.

4. The front and rear bearings of the main shaft of the cnc tube bending machine should be covered with high-speed grease, and the primary shaft box embraces mechanical seal, so there is no need to include grease.

clamping cylinder of tube bending machine cnc.
We are one of the greater credibility cnc tube bending machine makers in China. We promote sale our cnc tube bending machine in India, Pakistan, Vietnam, Chile, Mexico, and get very good feedback from our customers. If you have technical concerns about cnc tube bending machine , do not hesitate to contact us, we will more than happy to assist you fix them.

Why Choose our CNC Tube Bending Machine?
With 16 years' experience, we have exported our nc and cnc tube bending devices to South Africa, India, Pakistan, Philippines ...
We produce all type of CNC tube bending machines, which match various industries, like the furniture industry, sports devices, boiler market, auto industry, bike industry. We can also do unique design and production to fulfill customers' production need. We can provide not only cnc tube bending machine however also tube forming services.
We offer user handbook for installation, repair and maintenance of cnc tube bending machine, and our engineer provides service of responding to questions of the consumer so that the consumer can utilize cnc tube bending machine properly.
Our cnc tube bending machine can help a lot in the production of tubes that have complex shapes and several curves. Its high flexing speed and high flexing accuracy can not be replaced by other devices. Our cnc tube bending devices for sale use good quality product, offer you best cnc tube bending machine cost and pipe flexing solution.
Here's my website: https://maquinaria-y-equipo.com/cnc-tube-bending-machines