Notes

<h1 style="clear:both" id="content-section-0">FORTE SUPPLY/SPACEMAN USA Broomfield CO, 80020 - Cortera ... in Midland Texas</h1>


Press RESET buttons b. OPEN draw handles (DOWN) for 10 to 15 secs to eliminate stress in cyndrical tubes a b 8 10 Cleansing: 2. Dismantle NOTE: Prepare dishwashing location before disassembly, utilize bucket to momentarily keep big gotten rid of components as well as a little container for O-rings, and also have a towel nearby to capture excess water.

2. If machine has air pumps, disassemble them 1. Turn power switches OFF a. OPEN draw takes care of to verify zero stress in cylinders; twist air tube ports to unlock as well as detach air tubes 1 b. Take air tubes apart totally; each air tube has O-rings (3 ), connectors (2 ), and check shutoff (1) c.

Rotate suction tubes to unlock and eliminate suction tubes, springtimes, as well as stoppers out of air pumps; watch that springtimes don t fly out e. Take suction tubes apart entirely; each suction tube has O-ring (1 ), spring (1 ), and stopper (1) f. Unscrew screws on air pump housings; different air pump covers from coverings g.

Get rid of dispensing door 3b a. Get rid of dispensing-door hand-screws (4) b. Eliminate dispensing door assembly from cyndrical tubes 9 11 Cleaning: 2. Take apart 4. Take apart dispensing door a. Remove beater guides (2) from door assembly; remove gaskets (2) from door setting up utilizing O-ring elimination device 4a 4b 4b b. Get rid of prime plugs (2) from door assembly; remove O-rings (4) from prime plugs using O-ring elimination tool 4c 4c 4d c.

Spaceman - Ignite Food Service in Jurupa Valley California
2018 SPACEMAN 6250 - Lot #, 2 Day Early Spring Construction & Transportation Public Auction, 3/6/2020, Jeff Martin Auctioneers Inc. - Auction Resource

Get rid of draw deals with (3 ), lowering initially to pop up draw shutoffs, after that drawing out e. Remove draw shutoffs (3 ), turning while removing to stop damage 4e 4f 4g f. Remove O-rings (4) and also H-ring (1) from draw shutoffs utilizing O-ring elimination device g. spaceman usa model no 6235h Turn celebrity caps (3) to ensure that tabs come; break off celebrity caps 5.

Get rid of beater settings up (2) from cyndrical tubes 5a 5b 5b b. Remove scraper blades (4) from beater assemblies; separate scrape blade clips (4) from scrape blades c. Carry out beater shoes (4) d. Eliminate drive shafts (2) from inside cylinders utilizing a dry towel; different gaskets (2) from drive shafts 5c 5d 5d Keep In Mind: If you experience assembly problem with drive shafts, Spaceman provides a customized removal device for acquisition.

Spaceman USA - Broomfield, CO 80020 - 303-997-5498 in Pearland Texas
Eliminate internal drip tray and also front drip tray + sprinkle guard 12 Cleaning: 3. Laundry All Parts CAUTION: Never clean parts in a dish washer. Always hand-wash components with safe, food-safe cleansers. 1. Verify power switches remain in the OFF setting 2. Make use of the huge brush as well as trendy water to extensively clean inside the cylinders; make certain to scrub the rear of the cylinders and validate the cyndrical tubes are free of ALL product 3.

Carefully tidy as well as clean down the beyond the maker 5. Very carefully and thoroughly wash all components gotten rid of from the device utilizing provided brushes, sponges, and clean towels; if equipment has air pumps, make certain to include all air pump parts in cleansing 6. When cleaning up the giving door assembly, clean the priming ports with a small brush 7.

Confirm all parts are tidy and also cost-free of all food item prior to re-assembling device 13 12 14 Cleaning: 4. Construct Care: Never ever compel the installation of any components. If parts put on t seem to fit, get rid of all parts as well as repeat setting up.

Location drive shaft gaskets (2) on drive shafts (2) b. Seal gasket open rooms with Spaceman lubricant, prolonging onto drive shafts as well as preventing the leading square components c. Insert drive shafts right into back shell bearings at the rear of the cyndrical tubes, and also transform them till the vital involves firmly into the outlet (when inserted correctly, the drive shaft will no longer turn 360) 3.

Spaceman USA LLC · 224 Commerce St, Unit A, Broomfield, CO ... in Anaheim California
FSX, the Food Service Exchange, is the commercial food service industry's go-to source for purchasing overstock, discontinued, and scratch-and-dent equipment and supplies, and you will be shocked at how good our prices are (an average discount of over 50% of today's market price).
The FSX online marketplace provides restaurants, caterers, schools and other food service facilities with access to a wide assortment of products. The exchange allows for direct sales between pre-approved sellers and buyers, ensuring a seamless, reliable, and fast timely transaction process. Whether it is a model from a previous year or an item with a slight imperfection, buyers can purchase anything they need from our extensive pool of pre-selected, certified top equipment manufacturers and dealers. With Food Service Exchange, customers can expect premium equipment and supplies, amazing prices, timely shipping, and consistent satisfaction. Find out more information today about FSX Food Service Commercial Kitchen Equipment and Restaurant Supplies at 20 - 50% off market prices, with a minimum 90-day warranty. Plus, 5-star customer service reviews, unmatched 90-day warranty, and always free shipping!
Connect beater shoes (4) onto beaters (2 ); when properly put, neither shoe overhangs beater edge 3b 3a 3c 3d b. Install scraper blade clips (4) onto scrape blades (4) c. Fit scrape blades onto beaters (2) d. Insert beater settings up into cylinders, making sure beater footwear remain in area; turn assemblies until they engage the drive shaft tricks and no more transform Install giving door 4a 4b 4c 4d 4e 4f 4g 4h 4i a.

Push prime connect into holes on top of dispensing door c. Insert attract valves into dispensing door, O-rings-first; center draw valve goes in the center as well as ports face outside d. Set draw deals with (3) right into slots on giving door, with adjustment screws encountering down e. Slide retention pin via draw takes care of; protected with nut f.

Fit gaskets (2) right into grooves on rear of door, level side out; slide beater guides (2) over beater rods (2 ), with flanged edges against the door h. Insert dispensing door assembly into cylinders, beater poles initially, pressing takes care of completely up as you put 13 i. Secure door setting up in a cross-pattern making use of handscrews (4 ), with the lengthy hand-screws (2) on the top 15 Cleansing: 4.

Frozen Beverage Machines Archives - Spaceman

If device has air pumps, construct as well as mount them 5a 5b 5b 5c 5d 5d a. Area O-rings on back shells, layer with Spaceman lubricating substance; mount equipments right into shells (they only fit one instructions) b. Link covers and also shells, guaranteeing they fit flush; protect with hand-screws c. Area O-rings on suction tubes; gently lube O-ring areas d.

Spaceman USA 6455H Service & Parts Manual in Madison Wisconsin
Insert suction tubes into pumps; revolve to secure, and count on wanted overrun setup 5e 5f 5g 5g 5h 5h f. Layer air pump drive shafts with Spaceman lubricating substance g. Mount air pumps onto equipment: insert at an angle while pushing air pump in, slightly turn to and fro until the equipment involves the air pump drive shaft push in as well as revolve counter-clockwise to secure place h.

If device will certainly go extra, set up air tubes right into receptacle, but do not connect to air pumps; or else, established air tubes apart until after device has been primed 6a 6a 6. Set up receptacle covers, agitators, as well as drip trays a. Layer within agitators (if present) with Spaceman lubricant and also set up with arrow pointing up b.

If maker will certainly be left unused, set up air tubes and also area hopper lids ahead; or else, set air tubes apart until after maker has actually been topped 14 16 Sanitization Sanitiza- IMPORTANT: After disinfecting the machine, DO NOT rinse or touch areas that have actually been disinfected. Product has to be included right away.

Sterilize maker prior to using once again. If warm water is needed to liquify sanitizer, enable the option time to cool prior to including to machine. If mounted, eliminate hopper lids and also air tubes 3.

Jerry Pelley's email & phone - Spaceman USA's Manager in Santa Ana California
Allow solution to agitate for 5 to 10 mins; Never ever leave maker on Laundry for even more than 10 mins 9. While agitating, gently utilize a clean brush to scrub as well as disperse sanitizer remedy along receptacle walls 10.

OPEN the draw valves (DOWN) and drain service from the equipment 12. https://controlc.com/57e5ce4d Press RESET switches to stop cycle 17 16 18 Frozen Item Operation Include product to device 1. Verify maker has actually been just recently disinfected (within 1 hour); if device has actually not been recently sterilized, confirm door hand-screws are tight, and also carry out sanitizing steps (Web page 15) 2.

Fro-Yo Girl Speaks: Spaceman USA and FroCup.com's End of the Year Soft Serve Machine Trade In Program

Area pail or big container below draw valve 4. Put 0. 25 gallons of product right into receptacle 5. If maker has air pumps, do not fill product over tiny air inlet holes on the base of the air pump 6. OPEN draw take care of (DOWN); sanitizer will certainly begin to drain draw shutoff 7.

Pour continuing to be product into receptacle 9. Raise the prime plug on the top of the giving door up until circulation is 100% product 10. Push prime plug back down 11. If machine has air pumps: Press RESET, after that press clean Guarantee product is coming out of the large hole near the top of the air pump Press RESET 12.

MODEL SM-6490H in St. Louis Missouri
Set up air pump air tube, putting air tube right into hopper, then rotate and insert air pump port into air pump; turn connector to secure area 14. Change receptacle lid NOTE: The mix-low lights illuminate RED when a hopper is short on item mix and instantly de-illuminate when device is loaded.

Product is currently prepared to ice up keep in mind: Guidelines think item is added one receptacle at a time. Repeat actions as needed 19 Frozen Item Procedure Freeze item care: Never ever separate air pump (if existing) with the equipment operating. If disconnecting air pump, first press RESET to stop operations and open draw manages for 10 to 15 secs to alleviate stress in cylinder.

Concerning Strength Supply Strong suit Supply is one of the world's leading carriers of icy yogurt devices and soft offer ice lotion machines.

Key compressor: 1x 6500 BTU, R404A Device positioning demands CAUTION: The device must be put on a degree surface away from wall surfaces as well as other objects. Tidy as well as properly lube device components prior to maker procedure. Tune-Up Set Caution: If this is the first time operating the maker, you MUST tidy and also disinfect ALL parts prior to running the maker. Carefully as well as thoroughly wash all components eliminated from the device using supplied brushes, sponges, and clean towels; if maker has air pumps, be sure to consist of all air pump components in cleansing 6.

Here's my website: https://controlc.com/57e5ce4d