Notes

It's The Myths And Facts Behind Saab 9-3 Key Replacement
How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have to follow a series of special steps to install a second ignition key. It requires dealer assistance using the handheld computer known as Tech-2. Then the transponder is replaced and a key are required to be purchased.

It is a good idea to rotate your keys in order that one does not get damaged faster than the other. This will keep your keys in good condition.

Replacement Case


In contrast to the traditional Saab keys of the past, the new key fobs contain electronics which makes it more difficult to copy. This has made car theft much more difficult than twenty years ago. However, it has made replacing lost keys a much more expensive task.

Every owner of a Saab 9-3 must have at minimum two working keys. If one of them is lost, it costs a fortune to replace it in the car because it involves replacing the CIM module and reprogramming the locking cylinders. Dealers charge between $100 and $200 for this.

There are ways to cut down on these costly costs. Certain parts suppliers will utilize the code of the spare key to cut a new metal blade for a fraction of the cost of the dealer. The key must, however, be the same as the original one to function properly in your vehicle.

You can also replace the case yourself by following these steps. You'll need an open-faced screwdriver and patience. With the screwdriver, slowly pry the plastic apart and separate the emergency key from the case. Once the case is open, remove the electronic components and place them inside the new case. Be sure to put the correct badge and key back inside the case, too.

Replacement Battery

The Saab 9-3 replacement battery is a low-cost part that can be quickly and easily replaced. This YouTube DIY video Cyclone Cyd will show you how to replace the battery for the remote key fob in only four steps. This tutorial should work for any modern saab key fob however, the procedure may differ slightly.

This button is usually located close to the Saab logo on the back of the fob. This button is typically located on the back of your fob close to the Saab Logo. Next take a flathead screwdriver into the small hole inside this button. This should be enough to open the fob case to allow you to change the battery.

After the new battery CR1632 is installed then you can reassemble your remote key fob and program it to your car. The entire process should not take more than an hour at most. This is a simple procedure that doesn't require special tools.

The process is more complex if you lose your key, but it's possible. saab key programmer must determine the VIN of the car and then order a new key blade and TWICE module with the exact unique code. The dealer will then have to program the key using MDI, a new software tool.

Replacement Key Fob

The key fob comes with an internal battery that is used to lock and unlock your car. The batteries last for a certain time and eventually go out of service. This is a frequent issue in all vehicles. The good thing is that you can change the batteries in most key fobs without having to replace the entire case. You can buy replacement fobs on Amazon that come with all the electronics already installed, so you can just pop open the case and replace the batteries in the original case. It's important to note that you'll need take out the emergency key first, and you can accomplish this by inserting the screwdriver of a small flathead into the slot in the middle of the case. The case will split when you turn the screwdriver around it.

If you're looking to replace your keys, keep a spare in your possession. This will save you a significant amount of money. If you have spare keys, you can request that the dealer cut a new key and program it into your car, which is cheaper than replacing the entire key fob.

If you don't have a spare, it is possible to add another key to your car, but this will require a lot of research and effort. The cost for adding a second key is a few hundred dollars, and it also requires programming of the car's computer. This can be accomplished by a professional, but it's a costly choice for the majority of owners.

Replacement Ignition

As opposed to the earlier Saab automobiles, the current SAAB 9-3 models are equipped with an upgraded alarm system that is built around a coded key. This means that if you lose your only working key, replacing it with another one can be very expensive because the car needs to have a computer module installed and it also needs to be specifically programmed to accept an additional key. Even a dealer can charge hundreds of dollars to program an entirely new key, even if they're unable to complete the task.

If you've lost your only working key the dealer will replace your car's computer (known as the CIM or SAAB TWICE) to create a replacement, and they will charge top dollar for it. We can reprogram the current EEPROM of your car's computer so that it is ready for an additional key. This will save you more than 50% on the cost you would spend at the dealer.

If you've been a faithful owner of an 03-11 SAAB 9-3, then you probably realize that the ignition key isn't really all that durable. If your ignition key isn't working properly, you should look into replacing it. They can become sticky and the buttons have been known to fall off. Luckily, replacing the ignition key isn't as complicated as it seems and can be done fairly quickly using the proper tools.

Read More: https://www.thekeylab.co.uk/saab-car-keys/