Notes

A Productive Rant About Motorbike Key Replacement
What to Do When You Lose a Motorbike Key

If you lose your motorbike key, it could be a stressful situation. It can be very frustrating to lose your motorbike key and then be without a vehicle for many weeks.

There are a variety of ways to have a brand new motorcycle key made. While many of these are simple and cost-effective however, some require a trip to the dealer.

1. Unhook the ignition Cylinder

The ignition cylinder is an essential component of the engine. If the cylinder is damaged, it can cause issues with the motorbike's starting. A variety of wires and components are responsible for the ignition function. If the cylinder isn't working properly, you will require a replacement.

The first thing you have to do is remove the ignition cylinder from your motorcycle. This is a simple job that anyone with the right tools could do.

To remove the ignition cylinder, you will need to disengage the upper triple clamp. This is a straightforward procedure which involves removing both handlebars and the upper triple clamp from each of the fork tubes.

After you've removed both handles, use a 22mm socket to loosen the pivot bolt. The bolt is massive and is used to secure the bike's top triple clamp. To remove the bullet connector from the top clamp, you'll need to remove it.

To prevent any harm to your body, it is important to work in a clean space. It is recommended to lay an unclean towel or sheet down on the floor to shield your body and make it easier to be able to see what you're doing.

It is a good idea, after removing the triple clamp to take measurements of the positions of the fork and bars tube in the triple clamp. This will allow you to reposition them exactly the same way when the new upper tripleclamp is installed. This can make it easy to place the fork tubes and bars back into their proper positions even if it was not possible to make the right choices when you first installed the upper triple clamp.

Next, unhook the ignition switch and wiring harness. To do this, you will have to unplug the large plug and then unplug the bullet connector.

This step is necessary should you decide to take the fairing cap off of your motorcycle before you start. This will allow you more space to work in.

2. To unlock your locksmith, enter the Key Code

A key code is an arrangement of numbers and letters which represent the characteristics of the lock. Locksmiths make use of key codes to create new keys and to repair or replace locks.

They are typically made up of a combination of numbers and digits, however, they can also contain letters. These numbers are needed to ensure that the locksmith creates an appropriate lock key for you.

Locksmiths have access key codes which can be used to create new keys. Some locksmiths convert the codes into keys by using computers. Some locksmiths prefer large reference manuals to determine which code they must use to cut new keys.

There are two kinds of key codes that the majority of locksmiths employ to make new keys. The first is a blind code which represents the specifications of the lock using the combination number and digits. The second type of code is a direct-digital code. It is comprised of numbers that show the dimensions of the lock as well as the cutting patterns.

Locksmiths can scan the code with small cameras or other tools to see the cuts or make use of a code cutter. This will allow locksmiths to cut a new key from the code. Both methods of conversion of a key code result in a new working key that can be used inside your lock.

Locksmiths may have to impression the lock or detach the lock before they are able to start the code cutting process. This can be time consuming and requires a lot of skill, but it can be accomplished with practice.

Prior to arriving at the location, the best locksmiths will be able to evaluate the needs of the client. They will then choose the approach that is most effective for them.

If the customer is having a hard in reading the lock's code locksmiths can make impressions to determine where the pins are within the lock's cylinder. They'll then mark a blank key with these locations, which can take anywhere from 10 to 15 minutes once they've learned the method.

3. Then, take the key to a dealer

The loss of a motorcycle key can be an expensive nuisance. You might have to purchase a flatbed or an Uber, or buy a new key from the dealer. You don't have to lose your key to stop your bike's existence. There are ways that you can safeguard your vehicle and yourself.

Keep one in a secure compartment on your bike, or give it to a family member just in case you lose the original. This will give you time to locate an alternate in the case of a break-down or theft.

You can also buy a Bluetooth key finder that will send you an alert when your key is in close proximity, so you won't have to worry about missing it or leaving it at home. This can help you avoid losing your keys in the first place, so be sure you invest in one of these if the type who loses things frequently.

Another alternative is to call your bike manufacturer and request a copy its key code. It is usually printed on the key itself or a metal tab that is attached to the key. If you are able to locate this number, it will be the fastest way to have the new key manufactured and delivered to you.

It's also a good idea to have your VIN (vehicle identification number) recorded so that you can carry it with you when calling the dealer. Some dealerships will require the information to get a key cut for you and may require proof of ownership before they will cut your key.

The right key will also save you money in the long term, since it will reduce the expense of having your motorbike fixed or repaired. Many manufacturers offer keyless systems that are a breeze for people who don't have traditional locks on their bikes.

If you're the kind of person who has trouble remembering where your keys are, you might consider putting them into an waterproof container, or in your jacket pocket. This will be easier to find, and it will also help keep your bike safe while you wait for a replacement key.

4. Unlock the Lock

If you've lost the key to your motorbike, there's a few simple methods you can try to unlock. These methods aren't permanent however they can save you time and money by allowing you continue to ride your bike, even if you have to hire a locksmith.


The first step is to check the lock to make sure it isn't broken or jammed. If it is then give the inside of the lock a good spray of WD-40 to loosen any dirt that is stuck. After the WD-40 has dried you can put your key back inside to see if the procedure works.

Another possibility is that the disks inside the lock could be misaligned. This can cause the key to not fully turn. To open the nuts, gently turn them with the screwdriver.

Next, you can try to open the lock using a tool called lock picking. This method is typically employed to open expensive locks however, it can be used for locks with lower security. The main thing to be successful with this method is to be aware of your lock well and choose it carefully.

A Bic pen is an excellent option for this. It can be used on U locks and even unhook the cylinder from a tubular lock.

Another alternative is to make your own shim from an empty coke can. This will allow you to remove the wedge bolt that is in the bar end joint. This is particularly useful when the lock is on the lower part of the handlebars.

If the shim method doesn't work, you can try using a knife to cut the lock open. This old-fashioned and destructive method can work occasionally however it could cause damage to your bike.

Protective gear is crucial to avoid this. Wearing gloves and safety glasses are essential when working with sharp metals, such as a shank.

If none of these techniques have been successful, then it's time to call a professional. A professional locksmith will be able to assist you in getting your bike back into working order by helping you unlock the lock without damaging it.

Read More: https://www.thekeylab.co.uk/motorcycle-bike-keys/