Notes

Responsible For The Motorbike Key Replacement Budget? 10 Unfortunate Ways To Spend Your Money
What to Do When You Lose a Motorbike Key

It's incredibly frustrating losing your motorbike's key. It can be extremely frustrating to lose your bike key and be without a vehicle to go for several weeks.

There are many ways to get a new key for your motorcycle. A majority of them are inexpensive and quick, however some of them require a visit to your dealer.

1. Unhook the Ignition Cylinder

The ignition cylinder plays a vital component of the engine. If the cylinder is damaged, it could cause problems with the motorbike's starting. The cylinder contains many wires and crucial components that make the ignition function. If the cylinder is not functioning properly, you'll need to get it replaced.

The first thing you need to do is unhook the ignition cylinder from your motorcycle. This is a simple task that can be done by anyone who has the right tools and knowledge.

To unhook the ignition cylinder, you will need to remove the upper triple clamp. This is a simple procedure that involves removing the handlebar halves and releasing the upper triple clamp from the fork tubes.

After you've removed the handlebar halves, use the 22mm socket to loosen the pivot bolt. This bolt is large and holds the bike's upper triple clamp. To remove the bullet connector from the top clamp, you'll have to take it off.

To prevent any harm in the future, you should work in a clean area. It is best to lay a clean towel or sheet on the floor to protect your body and make it easier to observe what you are doing.

After removing the upper triple clamp, it's a good idea to measure the location of the bars and fork tubes are in the triple clamp to ensure that they can be put in the same order when you install the new upper triple clamp. This will make it easier to place the bars or fork tubes in the correct places even if you did not do everything right when you installed the upper triple clamp.

Then, disconnect the ignition switch and wiring harness. To do this, you will be required to disconnect the large plug and then unplug the bullet connector.

This step is necessary If you want to remove the fairing cap off of your motorcycle prior to you begin. This will give you more room to work in.

2. Take the Key Code to a Locksmith

A key code is a combination of letters and numbers which represent the characteristics of the lock. Locksmiths use key codes to make new keys and repair or replace locks.

They are usually composed of a combination number and digits however they may also include letters. They are essential to make sure that the locksmith creates keys that work with the lock you've chosen.

Locksmiths have access to many key codes that can be used for new keys. Some locksmiths convert the codes into keys using computers. Some locksmiths prefer large reference manuals to determine which code they need to cut new keys.

There are two kinds of key codes that most locksmiths use to create new keys. The first is a blind code that represents the specifications of the lock by using the combination of numbers and digits. The second type is directly digitized code which contains numbers that show the measurements of the lock as well as the cutting patterns.

To cut a new key using an existing code, locksmiths must either scan the code using small cameras or tools to identify the cuts made on the key or they can utilize a code cutter make a precise cut key. Both methods of converting a key code create a new working key that can be used inside your lock.

Locksmiths might need to stamp the lock or take apart the lock before they can start the code cutting process. motorcycle key is time-consuming and requires some skill, however it is possible with practice.


The most skilled locksmiths are able to evaluate the needs of the customer prior arriving at the site. They will then determine the approach that is most effective for them.

If the customer is having a difficult to read the code of their lock the locksmith can use impressioning to identify the pins' locations inside the lock cylinder. They can then mark a blank key using these pins. This can take 10 to 15 minutes once they've mastered the method.

3. Get the key to a dealer

A lost key to your motorbike could be a costly inconvenience. It's possible to pay for a flatbed or an Uber, or you might need to purchase a new key from the dealer. But losing your key doesn't need to mean the end of your bike's life and there are some ways to safeguard yourself and your bike when it occurs.

Keep duplicate motorcycle keys on your bike in a safe location. You can also give it to someone in your family or a friend in case you lose your original. This will enable you to have a spare in case of a theft or breakdown.

You can also purchase a Bluetooth key finder, which will notify you when your key is in close proximity so you don't have to worry about it getting lost or leaving it at home. This can help you avoid losing your keys in the first place, so be sure you purchase one of these devices if you're the type of person who loses things frequently.

Another option is to contact the bike manufacturer and request a copy of its key code. This is often written on the key or on a metal tab that is attached to the key. This number is the fastest way to get a new key made and delivered right to your door.

It is also a good idea to keep your VIN (vehicle ID number) recorded so that you can bring it along when you call the dealer. To cut a key for you, a few dealerships will require this information. They may also require proof of ownership.

A good key can help you save money in the long-term, as it can help you avoid needing to repair or replace your motorbike. motorcycle key offer keyless systems, which are more convenient for those who don't have a traditional lock on their bikes.

If you are the type of person who can't remember where your keys are, put them in an insulated container that is waterproof, or in your jacket pocket. It will be easier to locate, and will also ensure your bike is safe while you wait for a replacement key.

4. Lock the door

If you've lost the key to your motorbike, there's some easy methods you can try to unlock it. These methods aren't guaranteed however, they can help you save money and time by allowing you to use your bike even if you have to hire a locksmith.

The first step is to check the lock to see whether it's jammed or broken by debris. To get rid of any dirt or debris, spray the lock with WD-40. After the WD-40 has dried you can try putting your key back into the lock to test if it works.

Another possibility is that the discs inside the lock aren't aligned correctly. This could cause the key to not turn completely. In this situation, you'll need to gently turn the nuts using an screwdriver to release them.

The next step is to use the lock picking tool to unlock the lock. This is a method used to unlock expensive locks. However, it can also be used to unlock locks that are less expensive. This method is ideal if you know your lock well and are careful when picking it.

A Bic pen is a good option for this. It is a great option for U locks and can even be used to remove the cylinder of a tubular lock.

Another option is to create the shim from an empty coke container. This will let you remove the bar-end joint wedge bolt. This is particularly useful when the lock is located situated on the lower portion of the handlebars and allows you to remove the handles with ease.

If the shim method fails you may try using a knife to open the lock. This old and destructive method may work at times but it can cause damage to your bike.

To prevent this from happening, make sure to wear protective gear. A pair of gloves and safety glasses are essential when working with sharp metals such as a shim.

If none of these methods have been successful, you need to get in touch with a professional. A locksmith with experience can unlock your lock and get your bike running again.

Read More: https://menusister7.doodlekit.com/blog/entry/24840005/the-most-innovative-things-happening-with-duplicate-motorcycle-keys