Notes

How to Replace the Defrost Sensor in some sort of LG Refrigerator
During https://fixthingz-appliance-repair.com within a LG fridge model LFX21976ST, the particular defrost sensor explains to the main command board the heat in the freezer. Any time the sensor is defective, the defrost cycle may stop functioning, which finally causes the evaporator in the refrigerator to ice way up and the temperature within the fresh foods compartment to boost. When your appliance will be showing symptoms associated with a faulty defrost sensor, don` capital t worry, the step by step guide provided beneath will help a person replace the malfunctioning part.

TIPS ON HOW TO REPLACE THE DEFROST SENSOR INSIDE A LG REFRIGERATOR
Before starting virtually any type of repair, unplug your appliance. If you may` t move your own appliance to achieve the outlet, turn the particular electricity running in order to it off from the circuit breaker. Always wear function gloves and safety goggles to safeguard the hands and eyes from injury.

Start the repair by simply opening the deep freeze door and taking away the lower freezing food bin. Lift your back of the particular bin around launch the locking navigation bars. With the back again angled up, take the front conclusion in the bin away of the freezer.
Now remove the door assembly coming from the freezer bed rails. Locate both screws on the area of the rails which usually contain the assembly in addition to rails together. Acquire the screws out and about with a Phillips screwdriver. Once equally screws are taken out, lift up on the door assembly to be able to disengage the several locking tabs, in addition to then pull typically the door and shape off the track make it inside a safe region.
Push the side rails back into the particular freezer, and move the upper basket out. Depress the particular two tabs on typically the front of typically the basket to discharge that from the rails. Angle the top of the container up before lifting the entire assemblage out of the freezer. Force the rails back into the area.

With the holders out of the particular way, it will be time to remove the rails. Using a new Phillips screwdriver, take out the anchoring screws from the higher rail, first. Following your screws are eliminated, pull the rail off the deep freeze wall. Repeat the same process about the other section.
Now begin the bottom rails. Start with pulling the track out of the compartment to gain access to typically the connecting rod inside the back that will links the left and right rail. To disconnect the rod, launch the locking hook situated between the gear wheel and the mounting zone. Once you include the very first side off of, simply pull typically the other side from the opposite gear tyre. Push the side rails back in, in addition to work with a Phillips screwdriver to eliminate the bed rails through the freezer wall surfaces.
Together with the rails out of the way, you may make out the particular freezer? s back panel. First, together with a putty blade, open up the small rectangular gain access to cover situated in the upper right side corner. Insert typically the putty knife into the small gap in between the cover and even rear panel in order to disengage the securing tabs keeping them connected. Take out there the tiny access protect and place it apart. To eliminate the backside panel, reach directly into the opening an individual created and locate the locking tab connecting the backside panel for the freezer compartment. Once that will tab is launched you can start embodying the the section. When all the tabs are lumpen, lower the panel down to the particular freezer floor, and disconnect the two wire harnesses linking the rear panel in order to the back wall. Now you can pull the trunk section out of the particular freezer.


You possess finally gained gain access to to the defrost sensor, which is definitely located near typically the top right part of the evaporator. It is essential to be added careful while taking sensor out. Destroying the evaporator shelves or fins can result in a Freon leak, which can only be fixed simply by a professional. In order to begin the elimination process, cut off the three zip jewelry holding the defrost sensor in spot. Once all the particular zip ties are gone, you might take the defrost sensor out by first extracting the particular thermistor at typically the bottom then drawing out the blend from the top rated. When those 2 sections are free, you can detach the wire control from the rear wall of typically the freezer. Then thoroughly take the defrost sensor out involving the freezer compartment.
Before installing typically the new defrost messfühler, guide the higher zip tie through the hole inside the evaporator, so that you can secure the sensor once you include it connected. Now run the defrost sensor wire harness behind the copper mineral line and connector it to the refrigerator` s back wall structure. Route the wires along the aspect of the evaporator. As soon as the sensor is in place, safe it with go ties at the very top, center and bottom. Help make sure to lean the zip ties after you have tightened these people.
It`s moment to begin reassembling your freezer area. Plug both the cable harnesses mounted on typically the rear panel in to the freezer`s returning wall, and reinsert the panel simply by snapping it into place. Now re-order the small oblong access cover.
Reattach the underside two bed rails on each side regarding the compartment. After you have secured these the many of the you took out and about earlier, you can easily move on to the best two side rails. Once you are finished using all four rails, slide the base rail out of the freezer plus reattach the plug rod.

Finally, you can put the fridge door back in. To do, line up the tabs inside the door rails to the gaps inside the freezer rails, and lower the door assembly straight down until it snaps into place. As soon as the door is within place, perform a quick test by pushing the door in and out to ensure it opens and closes appropriately. If it does, you can place the screws inside of that holds the door to the side rails.
To accomplish your maintenance, get the top rated rails and put in the freezer basket and then drive the basket back into the compartment prior to reinstalling the bottom bin. Now that the refrigerator is reassembled, plug that back in and revel in your properly functioning appliance.

If the newly installed defrost sensor did not really correct your refrigerator` s problem, please contact us right now to schedule the appoint with single of our highly qualified appliance repair technicians.

Homepage: https://fixthingz-appliance-repair.com