Notes

Why You Should Be Working With This Vinyl Fences
How to Install a PVC Fence

If you have decided to install a fence, it is important to know that there are certain points to be aware of. First, determine the location where you would like the fence to be installed. Next, you need to prepare the ground. Then, you'll have to place the posts. You may also need to adjust the height depending on the size and shape of your property.

Preparing the ground

It is crucial to prepare the ground for the fence. This is because the fence posts have to be buried in a secure way. The fence can easily fall off if it's not secured.

Before you begin digging, you should check your local utility company to ensure there aren't any underground utilities that could block the construction. You can dial 811 to make sure that your yard is marked for underground lines.

You must also make a gravel base for your fence post. This will allow water to drain away from the posts. It will provide a solid foundation on which to place the blocks.

Once you have the base, it's time to install the vinyl fence. The fence should be a minimum of four feet long and 1 inch thick. If you have access to an auger, then you can use it to dig the holes for the fence posts.

Before you start digging, you must remove any plants and shrubs that may block the hole. In some situations it is much easier to remove the soil than it is to dig it. Avoid digging in sandy or rocky soil if you must.

Then, you should mark the highest and lowest points of your yard. This can be done easily using string levels. Attach the string level to stakes at least one foot above ground. The string level serves as a reference point for the fence posts.

If your land is in a climate that is extremely dry, you'll likely have to drill pilot holes prior to drilling. This will speed up the process.

You will also need to mark the holes. Spray paint or markers to mark your holes. To ensure straight posts, you may also use a mason's line.

vinyl fence install cost can also fill in the gap using decorative stones. These stones are ideal for small gaps. However should you have a larger gap, you will require a different approach. You could also try putting dirt in the gap. This is an affordable and cost-effective solution.

Set the posts in place

It can be difficult to put the posts in the right place. The first step is to locate the correct location. This can be done with an apex level, a line mark that has been painted to fit the width of the post or a measuring tool.

Next, place the corner and end posts in their place. Also, set the middle and top rails. Some cutting may be necessary. You could also use rails to act as a spacer between the posts.

After you have located the center of each hole Use a tape measure or stakes to mark the middle of the post. You can also draw the string line to determine the proper depth. After the string line has been drawn, tie the ends of the posts to the string. This will ensure that the fence will be straight.

After the posts are set after which you can fill the bottoms with six inches of dirt. This will help keep the posts in place and provide drainage on the base.

When setting the fence posts in concrete, make sure to use a quick setting concrete. This is a kind of concrete that is set in three to four minutes. It is not recommended to tighten the panels when installing privacy fencing. The panels should be placed 22 inches above ground. The panels is to be secured using #10 1" self-tapping stainless steel screws.


The posts can be attached to your vinyl fence using two screws. It is recommended to leave one screw at each end of the privacy fence. You can also cover the lower horizontal rails using duct tape prior to affixing them to the posts. This will prevent concrete from getting into the lower horizontal rail.

Once you are happy with the arrangement, take off the duct tape. Then, insert the top rail into each of the posts. The pickets can be affixed to the rails.

You can also put lower rails at the corners. You can use aluminum U-channel to secure the rails to the post.

Assembling the panels

It is crucial to align the fence posts properly in order to install a vinyl fence. Depending on the style of your fence, you might need to use different techniques. When you're installing an square or oval fence just a few simple steps can get you started.

Before you begin, be sure to read your deed and local Zoning laws. Inform neighbors of your plans. If you're planning to build fence made of vinyl it is possible that you will need to apply for a building permit.

Once you have all your posts in place It's time to install your rail brackets. These screws are fixed to the inside of the post. This allows for more control of the posts as they are placed.

Before setting up your rail brackets, you should install the bottom rail. Vinyl panels pre-assembled have two rails. You may have to cut the rails to suit your terrain.

Once the bottom rail is installed, you can put in your middle rail. The top rail can also be installed in the same way. You can use a aluminum u-channel for this process. You can insert it into your posts with the help of #8 x 1'' screws.

You can then install your pickets, one at a time. Once they're all in place and you are ready to begin attaching your C channel brackets. To hold them in place, you can place stakes at their corners. To join stakes using cotton string.

Spray paint markers can also be used to mark your fence. This will ensure that the fence is level when it is installed.

Additionally, you will have to install privacy panels. They should be placed on the backside of your fence. To ensure that they stay in place, you could also add pea gravel. If you have a gentle slope, you can address it by putting your fence panels at one side so that they "step down" to the slope. If the slope is steep your fence needs to be set up in a way that "steps down".

Problems with height changes

It might be difficult to align the posts when you want to build a PVC fence. There are two methods to accomplish this. One is to lay the posts on the ground and the alternative is to lay them out. The first method is simpler and ensures that concrete is laid under and around each post. The second method requires digging out the posts, and then backfill them with dirt.

Make sure you have enough backfill to keep the posts when digging them out. To place the posts in the base of the gravel, you will need to dig about six inches. To drill the holes, you could use a hole driller. The tension bar can be welded to the mesh at the end of the process. Attach the steel mesh at the top of the fence.

If you're having trouble aligning the posts and you are having trouble, you can remove the rails from posts that are too high. Although it is difficult, it is possible to do it with two people. If you have a hammer and chisel, you can tighten the threads of bolts. This will stop them from escaping the fence when you pull it out.

Homepage: https://provinylfencing.com/vinyl-fence-installation-services/