Notes

- C360 Overall EC - Gauging
--- Checked the customer comments raised by (Tom Yates) against Rev 3
--- Incorrect 3rd party letter attached
--- Setup a meeting with Richard on Monday 13:30

BoM comments for Dean:
x BoM Title, delete german
x Delete 'A Revision' notification 2x lines
x BoM name should have '-'
x Dean preparer
x Daniel checker
x TI7566-302-BoM - missing item 66

350/3/4
x P clip missing to the RHS immediately of the Y-piece (item 66)
x Remove arrow 21 from view F

350/1
x Shift the 2x RHS clamps onto their own platform
x P clip missing to the RHS immediately of the Y-piece (item 63)
x Remove arrow 21 from view F

Red pen drawings:
x - item 61 (conduit Y-piece)
x - item 62 conduit (top)
x - item 63 (3x new, cable clamps)
x - item 64 (45 deg gland)
x - item 65 (cable tie)
x - item 66 (p-clip)

- Pre-FiC EC Plan
-- Check on Friday

Make notes on the accuracy of the weighing (weighwell info)
-- 2019 will be less accurate than 2026 for cross axle loads (different weighing setup due to depot road restrictions)

- Speak to Carl Milner regarding TI 18308 Dispensation

Overall EC:
- Email regarding weighing of ripped out components - Chase up Sara
- Check the component weighing, chase up remaining non weighed parts - Chase up Sara
- PIS 21.5" Screen to grab pole jig LHS,RHS (Before 3rd FiC unit comes in, 22/05/2026)

RL:
- DWG-066 - RL to sign as approver
- Book Leading without formal authority (Ani/Grace could attend?) - https://www.imeche.org/training-qualifications/training-details/leading-without-authority - London 20-21 May 2026 (Wednesday-Thursday) - chase up in a week-ish

___
WSP clip (lower bracket):
- SF5000 bogie variations
- Service history from build on C360, C350/1/2/3/4
- Assumed ~30% of the axles ends have WSP clip on them
- SF5000 DMU bogies
- Mass 0.86 kg (total including bolts) - 0.5 kg for the strap
- Holds the same cable same form, fit and function.

___
Before 3rd unit comes in:
- Create a Jig which goes from bottom of floor plank to 3x boss holes (for 2nd unit) - top of floor to bottom of channel is 82-83 mm
x - Grab Pole Hole - Dispensation fix
x--- Note the Browns fastener photo DIN 912 M8x25 used for grab pole incorrect hole filling
x--- Grab Pole dispensation fix (DIN 912 M8x25 browns fasteners photo + Loctite 222 + counterbore hole 14 mm wide, 10 mm deep)

Download Creo View

Changes to Mass & CofG calculation doc (next rev):
- Cover sheet - Mass Calcs according to EN 15663 (not EN 13103-1) The mass according to EN 13103-1 is not specified as “MND”. MND load case is solely specified in EN 15663. Calculate average standing area (210 kg - 350 kg), should be 280 kg average
- Update formula for Original MXD TOS & DMOS1 tab (missing last row in total formula)
- Lateral CofG mm formula linking to wrong cell (comes out as 0) (Tare and crush)
___
To do:
- VMI Revisions E17460 - 10 VMI's
- Creo View Install
- Class 707 Wheelchair - EC - Chase up Southeastern/Siemens contact - Send to AH for review - Update docs
--- Work Instruction
--- 3353 - Appendix