Notes

biomass pellet making machine
Unsteady current of the biomass pellet making maker


The ring die as well as journalism roller of the biomass pellet making maker revolve at a constant rate, and the working state of each immediate is basically the very same. If the quantity of feed material is unchanged, the power intake must also be relatively secure, and also the existing will certainly be reflected on the electric motor. Likewise relatively steady.

When the biomass pellet making equipment device is working, we change the feeding quantity as long as the product density in the feeding area is less than the maximum beginning factor of journalism location, it will straight affect the size of the effective workplace of journalism location and journalism area, and also create the current to stream.

The fluctuation and also the change of the per hour outcome of the biomass pellet making device, as well as if the thickness of the product layer in the feeding location is higher than the maximum beginning factor of journalism area, along with enhancing the thickness of the material layer in the feeding area, it will not impact the hourly outcome and power usage per unit time.

If there is any kind of impact, it will certainly no more trigger adjustments in existing as well as biomass pellet making equipment outcome. Due to the fact that the density of the product layer in the feeding zone exceeds the optimum starting factor of journalism zone, the interval between journalism area as well as journalism area is constant with no modification. In the interval where the multi-feed product is located, the clamping angle is above the vital rubbing angle, as well as the product will certainly not be squeezed right into the pressing area.

By doing this, with the increase of the feeding quantity of the biomass pellet making machine, the balance of in and out is damaged, and the in is greater than the out, and the product layer in the feeding location is It will certainly gather thicker and also thicker until all the spaces are loaded and also blocked to the feed port, to make sure that the biomass pellet equipment can not function normally. Right now, the current will certainly increase.


In the actual job of the biomass pellet making maker, with the adjustment of the feeding quantity, the instant outcome and also the current of the main motor will transform as necessary. As well as when the feeding density does not go beyond the optimum beginning point of the pressing location, it will certainly not cause a growing number of material layers in the feeding location as a result of the boost in the quantity of powder we feed.

As has been stated prior to, the area that can trigger rapid result and power intake adjustments should be both areas of job and also product layers - the compression location and the biomass pellet device extrusion area, so we think that the third area pointed out over- - The affordable presence of the feeding location has specific problems.

That is to claim, the fed material layer is dispersed in the compaction area, the extrusion location and the feeding area whose overall thickness does not go beyond the optimum entrance factor of the compaction location.

The biomass pellet making equipment will certainly work usually under the allowed power. If the amount is also large and also surpasses the thickness of the maximum beginning factor of the compaction area, the product layer will certainly accumulate and progressively boost, and the biomass pellet making maker will not work normally. Current is varying.

Through the above richi pellet , let's talk about some phenomena showed by the biomass pellet making machine under 2 possible working problems:

( 1 )When the power of the main motor is not large sufficient compared to the equivalent biomass pellet making device granulation criteria, the thickness of our feed is at the end of the extrusion area and the optimum entrance factor of the compression area (this will vary with the raw products, compression ratio, effective length-diameter proportion, moisture, pressure rollers and also various other variable factors to readjust accordingly), generally will not exceed the optimum beginning point, with the boost of the feeding amount, the compression location will change appropriately.

The length of the period will be shortened, and the interval size of the press location will slowly increase accordingly, as well as the current of the main motor will additionally slowly enhance until it reaches the maximum allowable usage. If the current gets to the security worth we established, as well as the thickness of the feeding product has actually not gone beyond the density of the optimum starting factor of the biomass pellet equipment pressing location, if the feeding amount is enhanced, the safety and security system will act, as well as the excess powder will be discharged. In order to make sure the regular feature of biomass pellets.

( 2 ) Mean the power of the major electric motor is very large or the motor fails to overload after the density of the feeding product goes beyond the thickness of the maximum starting factor of journalism area due to the extensive adjustments of lots of variables. Right now, the powder fed to the people can not enhance the time output, neither will it create the boost of the primary motor existing, however can only continue to raise the powder pile collected in the machine up until the internal cavity of the biomass pellet press equipment is obstructed.

Create the biomass pellet making equipment to not work appropriately. Naturally, this unique phenomenon seldom occurs in actual manufacturing (if the raw product moisture is also big, the reliable element ratio is as well tiny, the pressure roller is seriously worn and also the void is not changed properly, the raw product is changed, and so on, this phenomenon might take place), this is our undesirable problems.


In-depth analysis of the very first generally made use of working state, it is not difficult to know that on the property that the relevant conditions are the same, with the modification of the feeding quantity, the interval length of the compression zone and also the extrusion zone is within a certain variety Corresponding modifications are also made (the feed flow rate is lowered, the size of the extrusion zone is lowered, and the length of the compression area is lengthened; otherwise, the extrusion area is extended and the compression area is shortened), and the feeding quantity does not exceed the pressure. When the density of the optimum starting factor of the tight area is concerned, the lengths of the above two intervals are not a constant value when this article is written. wood pellet making machine price the extrusion zone length value, the higher the biomass pellet maker production efficiency and the longer the pellet length per extrusion per roller.

Therefore, it is concluded that the factors of current instability under the condition of controlling the feeding amount need to be investigated from the moisture content of the raw material, the effective aspect ratio is too small, the pressure roller is severely worn and the gap is not adjusted properly, and the raw materials are replaced.

RICHI MACHINERY has been established for more than 25 years, specializing in biomass pellet making machine for sale, the development and production of single/complete pellet production lines such as animal feed, biomass fuel, wood waste, grass, straw, organic fertilizer, etc, and provide design and services for EPC/Turnkey projects!


Here's my website: http://prsync.com/user/777417/