Notes

Operating procedures of floating fish feed  device
1. Running treatments of floating fish feed machine

( 1) Safety measures before beginning and also after quiting

① Inspect all parts of fish feed drifting pellet making machine, especially the attaching screws and also anchor screws of each area of the puffing chamber, the attaching bolts between the electric motor base as well as the framework, as well as the screw link in between the puffing chamber as well as the structure, as well as there must be no looseness;

② Manually turn the main shaft, right now, there must be no massaging audio in the fish feed drifting pellet making equipment puffing dental caries;

③ Beginning the feeding auger of fish feed drifting pellet making equipment, inspect its stepless high-speed efficiency, and also require regular operation;

④ Examine as well as clean the water and also gas paths before starting the fish feed drifting pellet making maker, and all filters require to be cleaned;

⑤ Prior to beginning the fish feed floating pellet making maker, examine whether the circuitry of the electrical control component is right, whether the rotation of each electric motor is right, as well as whether the control is trustworthy;

⑥ After the fish feed drifting pellet making device is stopped, you have to wear high-temperature handwear covers, quickly remove the discharge mold and mildew, and right away clean it while it is warm, and also begin the major motor to clear the product built up in the puffing tooth cavity. When the corn is blown, soybean powder need to be included The material is rinsed clean;

⑦ Pay attention to safety and security when discharging the device, as well as do not stand in front of the device to avoid risk brought on by recurring pressure in the fish feed drifting pellet making equipment dental caries;

⑧ After the fish feed floating pellet making machine is running normally, it shall not be closed down at will.

( 2) Power on

① Prior to starting the fish feed floating pellet making machine, inspect the bolts, and also there need to be no looseness;

② Make sure the regular supply of heavy steam and water;

③ Make sure that the power supply and also electrical appliances are normal;

④ Open up the heavy steam valve, preheat the floating fish pellet maker blowing chamber, the temperature is about 100 levels;

⑤ Start the fish feed drifting pellet making machine: start the conditioner, start the feeding auger, when there is material spurting from the electrical outlet of the conditioner, start adding steam to the conditioner.

A percentage of water is included, and the product is fed into the blowing dental caries at the same time. After the material is squeezed out by fish feed drifting pellet making device, the puffing effect and moisture of the item are readjusted.

( 3) Downtime

After the fish feed drifting pellet making maker manufacturing comes to an end, it requires to be quit. The stop sequence is: feeding auger and conditioner. After that wait until the shown value of the primary engine present on the electric control closet comes to be the no-load current worth, after that stop the major electric motor and the oil pump electric motor.

( When the corn is blown, about 25 kg of soybeans need to be fed right into the bypass feeding port of the first area of the blowing cavity. To clean up the recurring corn material in the puffing dental caries, and afterwards stop the major motor to prevent the fish feed drifting pellet making device from obstructing), after that quickly disassemble the blowing cavity of the tail section for cleansing.


After cleaning, apply grease to the internal wall surface of the primary shaft and also screw head (After feeding oil), re-install it and wait on the next boot;

When you see that the product degree sign on the silo shows that the material degree has reached the lowest level, begin to get ready for closure. At this time, do not stop the feeding auger and conditioner, and also stop feeding when the major fish feed drifting pellet making maker present declines to the no-load existing auger and also conditioner.

2. Procedure series of floating fish feed maker

( 1 )When puffing soybeans, the two areas at the inlet end of the blowing tooth cavity are single screw heads, as well as the three areas at the outlet end are geared up with dual screw heads.


Initially, add steam to the jacket to preheat the blowing dental caries to concerning 100 degrees, and also placed the screws on the puffing cavity at the tail area. After the plug is tightened, loosen it for 3-4 turns, and after that tighten the screw plug to repair the screw plug before feeding.

By regulating the stepless high-speed manual fish feed making machine of the feeding auger, the feeding rate is from slow to quickly, and the feeding rate is from little to huge. After the soybean dish is expelled from the screw plug hole, add the cover to enter the typical manufacturing, and configure the screw connects with various apertures to acquire soybean dish with various returns and also excellences.

By setting up the conical stress rings of different diameters, the shown temperature of the four-section (discharge end) puffing cavity is 130-140 degrees. It is advised that the filter of the crusher made use of for crushing soybeans must have a size of 3-4.

( 2 )When squeezing out powdery feed by fish feed floating pellet making maker, the squeezing out screws in the squeezing out tooth cavity are all single screw heads, add vapor to the coat to preheat the puffing tooth cavity to regarding 80 levels, as well as go into the fish feed floating pellet making maker as well as steam uniformly relieved and toughened up powder.

Concerning 18%, this must be done in the feed conditioner, and also the feed amount is regulated by the stepless speed managing device from little to huge. Keep in mind that the reading of the ammeter of the main electric motor ought to not exceed the ranked existing of the main engine of fish feed floating pellet making machine.

Beware of overloading the motor as well as squeezing out powdery products. When the pop over here level of the squeezing out chamber at the discharge end is managed to an proper degree by configuring conelike pressure rings with various sizes.


The above is the principle, structure as well as operating treatments of the fish feed floating pellet making maker presented by Richi Equipment. In search of crunchy taste and also great look, producers commonly add a raising agent (or baking powder), which has a particular quantity of aluminum components, as well as generates gas when heated up during baking or frying, and also the leavening representative is inside the food.


Here's my website: https://atavi.com/share/xjviabz1hxr4k