Notes

Operating  treatments of  drifting fish feed machine
1. Operating procedures of floating fish feed machine

( 1) Safety measures before starting and also after quiting

① Examine all parts of fish feed drifting pellet making maker, particularly the linking screws and anchor screws of each area of the puffing chamber, the linking screws in between the electric motor base and also the frame, as well as the bolt connection between the puffing chamber and the frame, and there must be no looseness;

② By hand turn the main shaft, currently, there must be no massaging sound in the fish feed floating pellet making machine puffing tooth cavity;

③ Begin the feeding auger of fish feed drifting pellet making equipment, check its stepless high-speed efficiency, as well as require regular procedure;

④ Inspect and also clean up the water and also gas paths before beginning the fish feed drifting pellet making device, and all filters need to be cleaned;

⑤ Prior to starting the fish feed drifting pellet making maker, inspect whether the circuitry of the electric control component is right, whether the turning of each motor is correct, as well as whether the control is reliable;

⑥ After the fish feed drifting pellet making machine is stopped, you should use high-temperature gloves, rapidly eliminate the discharge mold, and also right away clean it while it is hot, and start the primary electric motor to empty the material built up in the blowing cavity. When the corn is puffed, soybean powder need to be included The product is rinsed clean;

⑦ Pay attention to safety when discharging the machine, and also do not stand in front of the device to avoid danger triggered by recurring pressure in the fish feed drifting pellet making device tooth cavity;

⑧ After the fish feed drifting pellet making device is running generally, it shall not be closed down at will.

( 2) Power on

① Before beginning the fish feed floating pellet making machine, examine the fasteners, and there need to be no looseness;

② Make sure the normal supply of steam as well as water;

③ Make sure that the power supply and electrical home appliances are normal;

④ Open the heavy steam shutoff, pre-heat the drifting fish pellet machine puffing chamber, the temperature level has to do with 100 levels;

⑤ Beginning the fish feed floating pellet making equipment: begin the conditioner, begin the feeding auger, when there is product flowing out from the outlet of the conditioner, begin adding steam to the conditioner.

A percentage of water is included, and the material is fed right into the puffing dental caries at the same time. After the product is extruded by fish feed drifting pellet making machine, the puffing impact as well as wetness of the item are readjusted.

( 3) Downtime

After the fish feed floating pellet making maker manufacturing comes to an end, it requires to be quit. The stop sequence is: feeding auger and also conditioner. After that wait until the shown value of the major engine existing on the electrical control cupboard ends up being the no-load current value, then quit the major electric motor as well as the oil pump electric motor.

( When the corn is blown, regarding 25 kg of soybeans ought to be fed right into the bypass feeding port of the initial area of the puffing dental caries. To clean up the residual corn material in the blowing dental caries, and after that stop the main electric motor to avoid the fish feed drifting pellet making machine from blocking), then rapidly take apart the blowing dental caries of the tail section for cleansing.

After cleansing, use grease to the inner wall surface of the major shaft and screw head (After feeding grease), re-install it and await the following boot;

When you see that the material level sign on the silo shows that the material level has reached the lowest level, start to get ready for shutdown. Currently, do not quit the feeding auger and also conditioner, and quit feeding when the primary fish feed drifting pellet making machine current drops to the no-load current auger and conditioner.

2. Procedure series of drifting fish feed equipment

( 1 )When blowing soybeans, the two sections at the inlet end of the blowing dental caries are single screw heads, and also the 3 areas at the electrical outlet end are outfitted with double screw heads.

First, add heavy steam to the coat to preheat the puffing cavity to about 100 degrees, as well as put the screws on the blowing dental caries at the tail section. After the plug is tightened, loosen it for 3-4 turns, and then tighten up the screw plug to take care of the screw plug prior to feeding.

By regulating potent pellet mill -speed mechanism of the feeding auger, the feeding rate is from sluggish to fast, and the feeding rate is from tiny to huge. After the soybean dish is ejected from the screw plug hole, add the cover to get in the regular manufacturing, as well as set up the screw plugs with various apertures to obtain soybean dish with various returns and finenesses.

By setting up the cone-shaped pressure rings of various sizes, the shown temperature of the four-section (discharge end) puffing cavity is 130-140 levels. It is recommended that the screen of the crusher utilized for crushing soybeans need to have a size of 3-4.

( 2 )When extruding grainy feed by fish feed floating pellet making equipment, the squeezing out screws in the extruding dental caries are all solitary screw heads, include vapor to the jacket to preheat the puffing dental caries to regarding 80 levels, and also enter the fish feed drifting pellet making device as well as heavy steam consistently quenched and also tempered powder.

Regarding 18%, this must be performed in the feed conditioner, and also the feed quantity is regulated by the stepless rate managing system from little to huge. Keep in mind that the reading of the ammeter of the main electric motor should not surpass the ranked present of the primary engine of fish feed drifting pellet making equipment.

Be careful of overloading the electric motor and squeezing out fine-grained products. When the chicken feed processing machine level of the squeezing out chamber at the discharge end is controlled to an appropriate degree by configuring conelike stress rings with various diameters.




The above is the concept, framework and also operating procedures of the fish feed drifting pellet making machine presented by Richi Equipment. In search of crispy taste and also great look, manufacturers frequently add a leavening representative (or cooking powder), which consists of a certain amount of aluminum elements, and also produces gas when heated throughout baking or frying, as well as the leavening agent is inside the food.


My Website: https://wordpress.com/reader/users/richipelletizerde799df132