Notes

Earthquake Augers - Installation and Operation

The Earthquake Auger is an agricultural device consisting of a steel pipe with teeth on both ends. It is used to break up hard-packed soil and rock to move it away from crops, homes, businesses, and other foundations that need to be built upon. You can dig as much as nine feet into the ground using this amazing tool. It can break through soil, concrete, rebar and any type of solid matter in your yard.


The Auger has a hydraulic system that allows for variable speed control. Two handles are located on the bottom of the unit. Each handlebar has a screw thread on the side that allows you to tighten or loosen the screw. On each side there is a trigger that can be used to increase or decrease the speed of the auger powerhead. There are separate controls for the firmness of the grip on the handles. The two handles rotate in a rotary fashion with each handlebar moving in a clockwise direction to pack the soil and the gas around the earth as you push the accelerator.


<img width="485" src="https://backyardequip.com/wp-content/uploads/2019/09/169291896-1.jpg" />

The total height of the Earthquake Auger is approximately ten feet. It is equipped with a manual choke as well as an automatic choke. When either is engaged, the auger will rotate once and then again to pack earth and the gas away from the area being excavated. The manual choke engages when the accelerator is depressed and the gas is flowing into the earth and the slow rotation increases suction pressure on the soil as the earth is sucked in. If either one of the handlebars slips out of grip, the accelerator will be depressed once again to resume the slow rotation mode.


This is an incredible piece of equipment. It is made out of heavy gauge steel and is very stable. https://billious.com/best-earthquake-augers/ However, if you use the auger to dig up hard packed clay or sod where the ground might be soft, the auger can be damaged. The hydraulic system in the Earthquake Auger consists of two separate gearboxes that spin the auger vertically as it rolls over the soil and rocks. These gears have an open design so they can slip over both roots and rocks. Once the gears are in place, the other gearbox shifts into an open position that allows the auger to push the clay and rocks together.


Most Earthquake Augers are powered by either a gasoline engine or a two-cycle engine. The gas engine may be more powerful than the two-cycle engine but it will cost you to buy gas. However, the two-cycle engine is cheaper and can also generate power through water pressure rather than electricity. The most important part of the Earthquake Auger is its trigger system. A trigger system is the part of the auger that allows you to cut the lines leading to the main sewer line without having to run new lines.


The trigger system is a two-stage system that allows you to cut the lines leading to the main sewer line without having to run new lines. The two-stage system is composed of a hydraulic auger that has a pressure controlled choke lever and a fishtail point. The choke lever allows you to limit the amount of gas and water flow through the auger. If there is not enough water or gas to push through the auger then the choke lever will close off completely. You do not want to have this situation because you will be wasting money on repairs.


To run the Earthquake Auger, you will need to set up the hydraulic control to your desired height. Next, you will put in the desired line and create the desired ground condition. After setting up the hydraulic control and creating the ground condition, you should set up the throttle which will allow the auger to move through the rock and clay at the desired speed. Lastly, you should test the choke and reset it to its open position.


After doing these steps, you should go ahead and slowly insert the auger all the way down to the earth's surface. This is where the real work begins because the force of the rock, mud and clay will cause the auger to be damaged if it is pushed too deep. You should make sure that the handlebars are level and that the ground is stable before you start pushing through the rocks. Once you get the ground's level, you should put on the throttle and start the movement of the auger. If you are using a good quality auger with a strong rubber tip, you should be able to move the rocks and mud at a very good speed.


Read More: https://billious.com/best-earthquake-augers/