Notes

The Way To Paint A Home - Exterior Paint Preparation

Is your property in need of some curb appeal? There’s perhaps no higher and more inexpensive method to add curiosity to your home’s exterior than by giving it a contemporary new coat of paint. Whether it’s time to attempt a new shade, or apply a fresh coat of the identical, an exterior painting project will assist protect your home’s siding and trim from the elements. And it’s one thing most do-it-yourselfers can do themselves. All it takes is the fitting merchandise and some advice out of your local dwelling enchancment retailer.


In this first video of our two-part sequence on exterior painting, we’ll present you the way to arrange the floor to ensure the paint correctly adheres to the substrate. We’ll reveal the most effective methods for cleansing the floor and eradicating flaking paint. And we’ll give you a similar floor preparation ideas the professionals use to make sure your end will last for years to come.



So let’s get started.

The first step in any painting mission, whether or not painting inside or out, is to ensure you might have a clear floor to begin with. To clean the siding of this home, we’re going to mix up a solution of 1 gallon of water, one cup of Tri Sodium Phosphate (TSP) and one cup of bleach into our sprayer tank. We’ll spray our cleansing and de-glossing answer onto the siding working in small areas. Then we’ll rinse with our pressure washer, ensuring we use a low angle, in addition to a low-strain tip designed for washing siding, just like the one I’m holding right here. As you’ll discover I’m absolutely protected throughout this course of, carrying a rain coat, rubber gloves and security goggles.


I’ve also positioned drop cloths and plastic sheeting on plants and anything that may be broken by this powerful cleaning resolution. We’ll begin from the highest and work our way down, working from aspect to facet.


One phrase of caution right here: stress washers could be dangerous. You should definitely read and observe the manufacturer’s instructions that got here with your stress washer. And by no means get the nozzle too close to the siding, as you might harm the wooden. Below high pressure, water from a pressure washer can etch wood, or drive water deep inside the wall cavity, the place it might probably lead to mold. As tempting as it could also be to use the pressure washer to blast of unfastened point, we’re only attempting to wash the siding and trim at this point.


Now that the siding and trim are clean, you need to give the floor plenty of time to totally dry. This would possibly take several days, but it’s essential that you don’t apply paint or primer on a wet surface. This is one of the leading causes of paint failure. When the floor is dry, it’s time to examine for lead paint earlier than going any further. Our house was built in 1972, and any house built earlier than 1978 may comprise lead paint. Following House painting ’s instructions that came with our lead paint take a look at package, we see that our siding does not comprise lead paint.



That’s a relief.

Now we are able to proceed to probably the most troublesome, but unavoidable part of the challenge … scraping and sanding.


Scraping unfastened paint from the siding is probably the most time consuming and exhausting a part of this mission. But it has to be executed to make sure correct adhesion. A few of the other ways to take away paint from siding embody energy scrapers, chemical strippers and even heat guns. But we won’t need these for our venture.


The tool we’ll lean on most to make the job go as smoothly as possible is that this carbide blade scraper. It has a handle that you hold with one hand, then with the other hand on the grip, pull the instrument towards you. Watch these loose paint flakes fall proper off. By no means push the scraper away from you or you can harm the siding. For the small channels in between siding panels, this stiff blade 1” scraper will do the trick. Just take your time and work the software to carry up on the edges of the flaking paint to get beneath it. Soon you’ll see the fruits of your labor paying off as more of the bare wood is revealed. However we’re not there but.


One thing most amateurs overlook in exterior paint prep work is sanding. With my random orbit sander and an 80-grit sanding disk, I’ll feather the edges as finest I can so there won’t be any seams between the old the new end coat. We also can use the sander to de-gloss any surfaces where adhesion may be an issue, like on this trim Just be sure you wear a mud mask to avoid inhaling any sanding dust.


Lastly, we’ll pull any nails and repair any cracks with some exterior glue, utilizing a number of end nails to carry it while the glue dries. We’ll additionally fill any nail holes with this exterior wooden filler and our putty knife. It will ensure no water penetrates the surface of our siding, which is vital to making our siding, and our paint finish, final . Now we’ll sand our patches easy with our random orbit sander. For areas we can’t attain with the sander, this sanding sponge will do the trick.


There you have it. While that actually took some effort and time, it was properly price it. Now we’re able to prime and paint the floor knowing that we’ve taken the right steps that can make our finish final for years to come back. Subsequent up: priming, caulking and painting.


In case you have questions about this or another home improvement venture, remember to learn our checklist of Regularly Asked Questions for this video. And you'll want to print out our Challenge Instructions, which includes a Instruments and Supplies checklist, earlier than visiting your native independent dwelling improvement retailer. That’s the place you’ll find all of the merchandise and useful recommendation to finish your mission. If you’re not sure the place to seek out your native store, examine our Retailer Locator. Good luck with your venture and thanks for watching.

Here's my website: https://mackaypaint.com.au/