Notes

What You Need to Know to Install a Washer and Dryer
How to Install a Washer and Dryer
Are you moving into a new home? What happened to your washer or dryer? Perhaps you just want an upgrade. The installation instructions in the owner's manual may seem simple, but washer and dryer installation can be dangerous. Because both water and electricity are involved in installation (plus gas, if you are installing a gas dryer), it is vital to connect every system correctly to prevent damage to the washer, dryer, or home.

Prepare for Washer and Dryer Installation
Before we begin, make sure you have these tools available:
Adjustable wrenches
Bucket
Pliers
Standard level
Towels
Vent brush

You should also double-check a few things if the new appliances will be installed where there isn't already a washer and dryer:
A 120-volt outlet should be used to plug in the washer.
Hopefully, you will install your washing machine near your hot water heater so that you can tap into the cold and hot water supply lines.
Be sure the machine will fit easily into the space you have available for installation. Measure the length and width of the machine before installing it.
Washing machines and dryers should sit on a firm, level floor. If not, the area under the machines can be damaged.

How to Install a Washing Machine
Our washing machine installation process is as follows:

Move the old machine away from the new one after disconnecting it
Ensure that the old washer drum is empty.
Unplug the machine.
Shut off the hot and cold water supply hoses and disconnect them from the shut-off valves.
Take the old machine away from the wall.
Disconnect the wastewater hose.

The second step is to connect the hoses to the new machine
The washer should come with water supply hoses and the necessary parts for a successful installation.
The technician will connect the water supply hoses on the back of the machine.
The other ends of the hoses attach to the valves for hot and cold water supply.

Step 3: Install the drain hose
The drain hose will connect to the back of the new washer and should drain into a nearby sink or standpipe.

Drain hoses that drain into sinks should be guided by plastic hose guides to prevent kinking.
The drain hose must connect to a standpipe otherwise.
When the drain hose has been installed, the technician will turn on the water supply valves to look for leaks.

Step 4: Level the washing machine
By doing this, you'll ensure the machine sits flat and won't walk or bang around once it's running.
Put a level on top of the washer.
The legs on the bottom of the machine should be adjusted with locknuts on the frame.
Test https://drainrooterusa.com/ of the machine by placing the level in the center, right, and left of the unit.

The washing machine needs to be tested. Plug it in now.

How to Install a Dryer
In order to install a new dryer, you'll need to ensure certain things. If you already installed a dryer in the installation space, it should be set up for success. Ensure that you have a reliable exhaust vent before anything else. In most houses, vents exit through a wall or roof. The second thing you should do is make sure that your power source is ready.
240-volt outlets must be controlled by circuit breakers of 30 or 50 amps if you have an electric dryer. For an upgrade to your electric dryer outlet, contact our colleagues at Mr. Electric.
To install a gas line for a gas dryer, you will need to possess the proper equipment. Licensed plumbing professionals are highly recommended for gas line installation.

When everything is in order, follow these steps to install your new dryer:

Step 1: Clean the dryer vent hose
It is important to thoroughly clean the dryer vent hose, as a blocked duct can pose a fire hazard. You can buy an inexpensive vent brush at most home improvement stores if you don't have one already.
To remove the vent hood, go outside and clear any debris at the exterior end.

Attach the vent hose to the dryer
You should be able to fit the vent hose easily over the hole on the back of the new machine.
Metal vent duct material is most commonly used for vent hoses. Plastic or aluminum ribbed profiles may need clamps when they are ribbed.

Connect the wall vent to the vent hose
The vent hose's other end should be connected to the wall vent.
A metal hose should fit neatly without any clamps or tape. If your tube is more flexible, you should use a circular clamp for it to stay in place.
Push the dryer into place.

Step 4: Plug it in
Plug your electric dryer into the 240-volt outlet if you already have it. Licensed electricians can double-check and install one if necessary if you're not sure.
A licensed plumber should help you install a gas dryer because the gas in your home will need to be turned off and on again for a safe installation.

Need Help With Washer and Dryer Installation?
Congratulations on your new washer and dryer! By scheduling an appointment with your local Drain Rooter Plumbing, you will avoid the potential risks and hassle of DIY installations

Homepage: https://drainrooterusa.com/